6651514593 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Woodstock, IL
- Parts Used:
- 4386996A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking where motor drive shaft enters pump
Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Eight Mile, AL
- Parts Used:
- W10844024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Wouldn't fill with water
Instructions very easy to follow
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from San Jose, CA
- Parts Used:
- WP8528862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leakimg a lot of water from under door.
Started down Parts Select list of possibilities. Replaced the door gasket (1/2 hour), still leaked. Replaced water deflectors (15 min), still leaked. Was looking at steam vent and read the repair submitted by "mary from Fountain Green UT". Removed and thoroughly cleaned the steam vent (1/2 hour). Stopped leaking and is working fine now. Repairs were very easy using Parts Select instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SELKIRK, NY
- Parts Used:
- 4318273
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad door switch
i took the inside door off and took the 2 switches out and replaced them; not too difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Woodward, IA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwasher leaking in lower front door area
Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matt from grant park, IL
- Parts Used:
- 676413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dish washer soap drawer would not work
we followed your instructions submitted via e-mail and they worked out just fine....thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Colorado Springs, CO
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old whirlpool soap dispenser latch wasn't working
Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Taylor, TX
- Parts Used:
- W11086533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Unfortunately, a mouse had made its home on top of our surround insulation. For hygienic reasons, I replaced the surround.
1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Republic, MO
- Parts Used:
- WPW10082894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Heating element would not heat
I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Little Rock, AR
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Top of the Soap Cap Latch was broken
The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrel from rosamond, CA
- Parts Used:
- WP8066018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lid Spring
Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Rehoboth, MA
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch worn out
Followed vidio instructionson web site. Quick easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Charlotte, MI
- Parts Used:
- 4318050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Broken door spring
The repair was very simple. Simply pull the dishwasher out far enough to access the springs, remove the old with pliers and install the new springs in the same spot as the old ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from Rogersville, MO
- Parts Used:
- W10844024
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The old valve has a small leak
Made sure the power and water were not connected to the dishwasher. Removed the bottom panel. Unhooked the old part. Put some plumber's tape around the threads, hooked it all back up. Runs just as good.
Was this instruction helpful to you?
Thank you for voting!
There were no provided instructions, just had to wing it.
Trial and error. The spring was difficult to install, the pin and door were easy.
Was this instruction helpful to you?
Thank you for voting!