58717345790 Kenmore Dishwasher - Instructions

Simple- Disconnect electric to washer, Remove inner door panel with philips screw driver, disconnect electrical wires watching exactly how they are to be replaced. remove star screws securing handle mechanism. Replace with new handle, connect wiring, replace inner door panel and your all set. Good luck.

Removed the screws that held the cover on, then removed the 2 screws that held the door latch in place. Disconnected the broken door latch and attached the new one. Put all the screws back in and that was it! Also, the shipment of the part was SO QUICK!

I clipped the wheels onto the rack. It couldn't be any easier. then i removed the # 25 torx screw which attached the broken slide wheel to the tub and installed the new wheel with the same torx screw.

Important - turned the power to the dishwasher off. took the screws out of the top part of the back door panel. pulled the wire leads of the broken switch, replaced the switch with the new one, reconnected the wires, put the panel back on.
Fixed

shut off the power on the breaker box, 6 screws inside the door on the tolp and side,pulled 4 wires off, 2 star head screws on the unit. took bad unit off,put new one on and put the screws back in.

5 minutes

I opened the control knob panel. The latch assembly is located behind inside the panel along w/ the wires. This is my second replacement of the assembly. The last one lasted about 2 years. They should make a sturdier latch assembly next time.

Removed the screws that hold the panel on ( just the top ones-no need to go all the way down the sides. Need a "star" headed screwdriver to remove the switch itself. Then removed the wires (4),one be one, so as not to mix them up. reinstalled all thescres for the switch, then the panel. Job done.
What amazes me is that Frigidaire doesn't read your page to realize that the handle assembly was defective and send out a recall. look at all the repars listed in your site , and these re just from the people that have responded with comments and who use your service. New handle/switch is much more sturdy with a higher density plastic that the original. Your service is easy to use, prompt and accurate. Fixed the dishwasher while my wife went to the store. Dishwasher done in 15 minutes and watched theNCCA tournament for 2hours in complete peace !!!!! No need to tell the wife only spent 15 minutes.

First i removed the screws on the back panel, unscrewed the latch, removed the wires and installed the new latch.
I found the latch is too expensive for a little plastic part.

Removed the screws on the inside of the door gaining access to the handle assembly. Lifted broken assembly out, inserted and secured the new handle assembly according to the directions.

The part was ordered and received the next day. The entire process was extremely easy. A repair person would have charged twice the amount of the part plus labor just to come out!!

First dissconnect power, and remove the 6 phillips-head screws from the back/upper side of the door, next remove the 2 torx screws holding the handle assembly, and unplug the 2 micro switches attached to the handle. Reverse this procedure and you're finished. It's so easy, a caveman could do it.

Before starting I disconnected the dishwasher. First I removed the door cover which then exposed the interior part of the door. I then used a star bit on the screwdriver to remove old latch. I disconnected the four wires to the door making sure that I made a point of which wire was connected to what. I then inserted the new latch and reconnected the wiring. Finally, put on the door panel and screwed in the remaining screws. About 15 minutes total work time.

First I removed the control panel and then removed the screw holding the handle. I then pulled the connector wires off and onto the new handle. I then screwed the new panel into place. Easy job, no mess.

removed screws to loosen front door panel then removed the wire connection, then removed the broken latch with screwdriver, installed new latch in same manner, fastened front panel back with the removed screws and I was back in business, easy as pie.

Removed the front cover by unscrewing the 8 screws. Removed the latch and attached new one. Re-attached front cover, and it works fine.
The gasket was in fine shape, and I question why I had to purchase the gasket in order to get the latch. Seems crazy and an unecessary expense on my part.

Take front off about 12 screws two screws held latch on took four wires off two white two black very simple to replace.