6651644590 Kenmore Dishwasher - Instructions

Disconnect power supply to dishwasher. Open door and remove screws on inner door cover. Carefully remove inner cover while watching how inner parts are arranged. Found return spring on detergent cup linkage had rusted and broken causing detergent cup not to open. Installed new spring and re assembled inner cover. Rotated timer dial one full revolution to check operation of detergent cup. Worked like a charm. Re connect power supply to dishwasher and your good to go.

I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassembled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!

After completely pulling out the dishwasher, I removed the rubber housing that connected to the housing assembly. I unscrewed the retaining ring which holds the impeller in place and then pulled the impeller off the shaft (which took quite a bit of force). I removed the seal seat ring and using the impeller and seal kit I replaced all the internal parts to the impeller system. (note: the impeller and seal kit acutally contained the seal-head and seal seat ring so I was able to return those two parts.) I put all of the disassembled parts back together.

I removed all the ( what my Husband called star screws ) star screws and removed the housing panel ( holds dish detergent cup and silverware basket ) I discovered everything accross the bottom was all gucked up with detergent soap accumulation. I took the part to the kitchen sink and used the sprayer hose on the part with hot water and it cleaned up beautifully, and the detergent latch then worked ( the spring that operates the latch was all gucked up with detergent accumulation ).
I am the wife and did all of this myself and it only took around 5-10 min. My Husband had to help me figure out the type of screws because they turned out to not be phillip screws, but as Hubby called them.."star screws".
Soooo, I did not need to use the Latch Kit I purchased, so will store it in my parts supply! :)
Happy repairs to you..
Judy Estes Park, CO

Removed the existing dispenser door, took off old spring. Slid new springs on pin, got it situated between the correct parts of the door. Popped it back on the pin inserts. Twisted spring into springing action position, voila. It was repaired. No repairmen. No additional costs, fees, nor extra time waiting on repairmen.

replaced the two water defiector's, I had changed the door seal and should have changed the defiectors at the same time. Save yourself some time and ordor both parts. This is a easy fix, anyone can do.

The old gasket came out easily, but had calcium deposits in area. I cleaned the area with vinegar and water and waited until it was completely dry. The new gasket went in very easily and looked great. I started the dishwasher and alas, it still leaks, so the problem was apparently not with the gasket, but some other area. But the gasket is nice and new. Any suggestions on next step0 in troubleshooting?

first i picked out the old seal, use a screwdriver to get it started. Then I pushed the new one in after cleaning the seal channel. I fixed it during a commercial while watching my favorite tv show.

I removed the inner nut holding the spray arm onto the pump. Turned the washer on it's back and removed the wire clip holding rear of the pump motor. Completely removed the pump housingand motor from the washer. Removed three(3) long screws holding the motor to the pump housing. Removed the dish from the housing and removed the old impeller and seals .
Cleaned the pump housing of calcium with lime-a-way. Reinstalled all new parts in reverse order as they order taken off. Cleaned inside of dishwasher with lime-a-away and general purpose cleaner. Reinstall pump housing and motor on washer in reverse order as they were taking off.
Reinstalled washer into cabinet and connected all hoses, drain lines and electrical wired. Turned washer on and watched it run throught a complete cycle. Worked just fine and no leaks. Parts were great.

Sincerely,
James

i took off the kick plate and found the water valve. its the piece that water comes to from under the sink to connect to the dishwaser. it has a plug with 2 wires. i turned off the water supply, disconnected the wires(probably should have flipped the breaker but didnt) took out the 5/16 mounting screws, had to use a little end wrench on 1 because it was behind the water line and a nut driver on the other. i put some thread gook on the connection and put the new one in the way it was and it works great. i am writing this because thats where i got the info to diagnose in the first place and saved me $$$!

Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.

i determined that the impeller was not free. ordered and installed an impeller kit which included a new bushing, which was the culprit. it was a fairly simple fix, needing only to remove the pump housing from the back of the motor. access to the impeller was by removing the screw-in, x shaped connection on the back side of the impeller housing. runs like new again. the fix was far less expensive than a new washer.

My husband did the repair. He sucked the water out with the wet/dry vac. Layed it over on the front and removed the pump motor and replaced it.

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

All I had to do was remove old door panel and retainer and I replaced with the new.
PartSelect were great. I highly recommend you guys.