58714012416B Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- steve from PT CHARLOTTE, FL
- Parts Used:
- 5304518927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower spray arm came off and melted on the header coil
took old one off by hand, snaped the new one in place by hand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Clinton, OH
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking tub seal
Just pulled the old gasket out and popped in the new. I did trim it too shrt however so be careful not to do that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marcus from NORMAN, OK
- Parts Used:
- 5304518927
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Spay arm came off hit the heater and burned a hold in the side
Easy just snapped on works going again like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Washington, DC
- Parts Used:
- 5304518927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Some of the silverware slip thru the silverware holder. During the drying cycle the exposed silverware was to close to the arm and melted an area of the arm which caused water to seep out onto the kitchen floor.
To remove the spray arm just squeeze the sides pull up and replace the new lower spray arm in it's place. Just push down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ANDERSON, IN
- Parts Used:
- 5304518927
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Spray arm came off, got melted
Snapped the new spray arm in place.
Works like new!
Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GENE from BRONX, NY
- Parts Used:
- 5304506521
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dispenser failed to operate
Uncomplicated repair. Remove door, remove old dispenser, install new dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from STEWARTSVILLE, NJ
- Parts Used:
- 5304532229
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing part
Just pushed it onto the rod that held the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Collierville, TN
- Parts Used:
- 5304500204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom seal on door came out and melted on heating element.
Took me about 2 minutes to repair, no tools to repair, very easy installation repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from ELK GROVE, CA
- Parts Used:
- 5304506521
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Plug for soap dispenser.
My future son in law did it. Looked at instructions on the app for the part. Didn't take very long.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from WOODBURY, MN
- Parts Used:
- 154827601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlene from Houston, TX
- Parts Used:
- 154430501
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Door Spring
First remove the kick plate.
Then look with a flashlight & mirror to make sure which, the spring and or the Spring Linkage are broken.
With the door open, to have less tension on the spring, replace the spring and or the spring linkage.
Attach the kick plate
Then look with a flashlight & mirror to make sure which, the spring and or the Spring Linkage are broken.
With the door open, to have less tension on the spring, replace the spring and or the spring linkage.
Attach the kick plate
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from N ROYALTON, OH
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
The heating element (ring) showed signs of wear
I followed the steps on YouTube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from COMSTOCK PARK, MI
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
My heating element was cracked
Remover the cracked heating element with the new heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from MEDANALES, NM
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Sprang a Huge Leak
I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
Was this instruction helpful to you?
Thank you for voting!