66517422990 Kenmore Dishwasher - Instructions

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

after that every thing went very well

follow the video, no problem, however, its still not draining after the cycle is finish now I don't know what to do.

Was very easy to replace broken spring which required each end of spring to be reconnected to bracket located on the door and frame of the dishwasher. Was able to complete without moving the entire dishwasher frame.

Followed instructions as the videos on this page show.

door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking

New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you

I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

Getting the dishwasher out was easy. Getting to the impeller was easy. Getting the impeller off of the motor shaft was the difficult part. I had to use my Dremel tool with lots of cutoff wheels to cut the impeller off of the motor shaft a little piece at a time. It appeared to be rust on the motor shaft that was causing the impeller to not come off. There is not much room for the Dremel so be careful not to nick the pump housing or cut into the motor shaft. Keep the vacuum close by to clean out the plastic impeller shavings. Clean the rust off the shaft with steel wool, fine sandpaper etc. Assembly was easy once everything was cleaned up.

Disconnected hoses (2) from pump housing. Disconnected pump housing from motor (3 allen screws, not too acessible). Unscrew spray arm from pump housing (this is done by hand; no tools as the "nut" is about 3" diameter and made of plastic) Open up the pump casing and replace impeller and the bearings on each side. The thing that takes some time is to mop the water that comes off at almost each step. There is probably an intelligent way to drain everything first. I did not order the large seal (kind of a large rubber donut, larger than a donut) between the arm and the pump and I shoiuld have as it was difficult to keep the old one from not leaking: Since by hand you cannot tighten the large nut very hard and tools could damage or break it. Applying upward pressure on the pump while tightening did it. (The pump and motor are all mounted on flexible mounts, like the heavy hoses connecting to the pump housing, so that there are no vibration.)

Ordered part, recieved part package, opened package, inserted screw cap rinse aid tank cover, twisted to close. Job completed. Time required about 15 seconds from opening package. Service was excellent and accurate. Thank you.

Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.

I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.

Unfortunately it still doesn't work. I asked Ina email to your company for any suggestions, No reply.

This is a portable dishwasher.. so first I turned power off and connected water line. When I turned the water on I noticed the water would flow into the dishwasher. This is not suppose to happen. This told me it was the flow valve. I disconnected water line, turned power off and removed bottom plate, removed screw holding valve on, removed water hose and output hose and unplugged valve. Then installed new valve. Turned water on to test and water did not flow into unit until cycle started. So simple. Problem solved in 10 minutes.