36315212100 Kenmore Dishwasher - Instructions

Removed screws on the drain pump filter screens at the back of the dishwasher, unscrewed the check valve, screwed in the replacement unit, and re-affixed the filter screens.

I lived with the drain problem for 6 months and reviewed on line trouble shooting which all pointed me to a pump or solenoid valve problem. I pulled the unit and disassembled everything before noticing that the rubber washer/stopper at the top of the check valve had erroded away and was not preventing water from pumping back into the cabinet when the drain pump kicked on. Always check the condition of this check valve first if you dishwasher is not draining properly. It was so easy once I found the bad part.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

As suggested. Pull washer, remove screws from top and replace with new part. Very simple and easy if you follow steps furnished by this site.

We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.

I removed the dishwasher, removed the front kick panel, layed the dishwasher on its back, loosened the clamps and removed the old motor and pump assy. Cleaned up the area where the unit was, Installed the new unit, tightened the clamps and it was done. Probably took around an hour because of my cleaning up the sealing areas.

Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.

Thank You
Debbie Bradford
Hookstown, Pa.

I removed the two screw at the top holding the dishwasher to the counter top; pulled on the unit - but found it stuck on something.
Of course the hot water feed and the drain hose were still connected and would not let the unit move out any further as there was no slack.
If I had thought about it - I would have disconnected these from under the adjacent sink. But I ended up lying on the floor trying to disconnect them from underneath the unit. It was a bit difficult as there was very little room to move the wrench and the screwdriver.
Once done, the unit came out very easily.
When tipped over I disconnected the old motor and replaced with the new. It was a very different design but fitted in very easily. The hanger took a bit of working out as the diagrams are not very clear.
The wires and clips went together easily. Once I had cleaned everything around the motor and the gunge that cames from years or washing dishes, it went back the way it came out. Albeit with the same difficulty with feed and drain hose.
We ran the unit with no dishes for a couple of times to clear our the muck left in the pipes when the system was down.
Now we have a fully functioning dishwasher again. Cost $250 for the pump and motor as opposed to the $800+ unit my wife was looking at!

First of all this site is awesome. So helpful in diagnosing and ordering the part. I highly recommend!

So, the solenoid was melted and needed to be replaced. If you're looking from the front of the dishwasher it's on the left side and it has 2 screws and a c ring. I couldn't get the c ring back on, but the piece stays on without it. Works fine now.

The instructions provided are very good if I had done before. My concern was getting the gasket to sit properly at the bottom where you cannot see. I removed the inside of the door (7 screws) and this made it easier to assure gasket sat properly in the track. may have cost an extra 15 minutes but worth it. If I do again I will take door apart again, however I think this is fixed and should not need attention again.

I took the old one off and replaced it with the new one, which fir perfectly.

Repaired by watching the video provided on my computer by this site . This video was a life saver and covered every detail. My thanks to this site !!!

See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.

Order the part through you guys and also ask to see if there could be something else wrong. I got an e-mail back the first buisiness day and you sent me the part that day also. I installed the coil and it's be running good ever since. Thanks for your speedy service and technical support.

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

I took the inside door off as shown in the gasket insert video and it made much easier to clean and insert the door gasket.