66515707990 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from Warrenton, VA
- Parts Used:
- WP8539324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plastic Mount was broken for upper level.
We unscrewed the old mount, and installed new mount, inserted screw and tightened. Waa-lah, that was all that needed to be done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from Springville, AL
- Parts Used:
- WP8539324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mounting hardware was broken
Removed the screw that held the mount in place. Snapped the new mount place (no screws required).
Fast & easy.
Fast & easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Danville, PA
- Parts Used:
- WP3376846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher wasn't cleaning the dishes
I removed the bottom spray arm and replaced the worn part. Now the arm turned freely and was performing as it was designed to do. I appreciate parts select for having the part available since the manufacturer no longer supported the model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from DANVILLE, PA
- Parts Used:
- WP8539324
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken spray arm mount
Removed holding stew from old style bracket. Put arm together with new mount and installed screw. Aligned arm with upper rack and just clicked on. Ensuring spray arm spun freely and done!
Was this instruction helpful to you?
Thank you for voting!
The 'nozzle' end of the arm tube fell into the bottom of the dishwasher, and was partially melted by the heating element.
One screw was taken out, the old arm removed, the new one put in place, then attached to the new arm tube holder. TADA!!!! Done.
I am a widow, and think I saved about $75.00 doing this job myself. Thank you.
I am a widow, and think I saved about $75.00 doing this job myself. Thank you.
Was this instruction helpful to you?
Thank you for voting!
Dishes Would Not Get Clean
First I removed the plastic bolt that holds the wash arm in place This exposed the upper ring that was worn out . I then lifted the arm off which exposed the larger ring. I replaced that ring, and then I put the arm back on and replaced the upper ring. I put the plastic bolt back in place and the repair was complete.-- Really Easy plus the dishwasher gets the dishes clean now
Was this instruction helpful to you?
Thank you for voting!
SOAP DISPENSER DOOR DID NOT CLOSE.
WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Salinas, CA
- Parts Used:
- WPW10253040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The coating on the upper rack had rust coming through.
Removed the plugs in the slides, removed the rack, slid the new rack in and replaced the plugs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Winnemucca, NV
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
dish washer leaking
Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ed from potomac, MD
- Parts Used:
- WP3378138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The soap dispenser lid was broken
I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Sherwood, OR
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
A spring was broken in the disposal chopper
I bought the kit because it had other parts that I thought I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from YORKVILLE, IL
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
1/4 inch bolt frozen to shaft
The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.
Was this instruction helpful to you?
Thank you for voting!
water coming out of the washer flooding the floor
I guess some food got caught in the water level sense float and caused it to mal function.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Ulysses, KS
- Parts Used:
- WPW10509257
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dish washer leaking out bottom of door
New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from SHELTON, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
DOOR leaking
door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking
Was this instruction helpful to you?
Thank you for voting!