36315565791 Kenmore Dishwasher - Instructions

Not really difficult to do. First remove the washer from the counter and flip it over. Carefully determine the correct drawing in the instructions which matches your machine. Follow insructions and double check everything. Took about an hour - and I saved about $350.00 by fixing it myself rather than buying a new one!

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!

I went to your site and check all the diagrams and then read the postings from others. I turned off the electrical breaker then took off the lower cover of the dishwasher. After disconnecting the water and electricial connections I was able to remove the 2 screws holding the unit in place and it came right out. I turned the unit over and was able to just remove the old part and put the new part in place. The whole job took me about one hour but I had never worked on a dishwasher before. Your site made the repair very easy to do on my own.

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.

The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.

The dishwasher runs quieter and the dishes come out clean now.

Removed the front door panel myself... pretty easy
Removed the lower panel myself... pretty easy
Tried to put new door panel & lower panel on....
had to call the x-husband to come over & do it for me! UGH!!!! HA! He is very handy and it took him a long while. Screws are not easily accessible.
But, it looks like a new dishwasher now!!! Thanks!
The moral of this story is... if you are a women... call a man to do this job!

I pulled the two clips in the rack guides and pulled out rack and reinstalled the new rack and put the clip back in the rack guides

Thanks for your prompt shipment of the rack I ordered

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

After researching for a few minutes on this site I was pretty confident that the problem I was having was a faulty check valve. I removed the 4 screws holding the cover in place at the back of the dishwasher tub, twisted out the check valve and saw it was obviously shot. I ordered the correct part and 2 days later I had the dishwasher working like new. Installation was a simple as could be....twist in the new valve and reinstall the 4 screws.

After running a test cycle and realizing the pump was working but not pumping all the water out, I checked the troubleshooting guide and parts list.
I found there was a check valve at the back of the machine and when I removed it I saw it was split causing the water to return into the unit. I ordered and replaced the check valve and the unit is back in perfect operation.

Remove old piston assembly with screwdriver and tapping hammer inside the machine and screw the new part in hand tight, all done works fine

I read the reviews on line and followed the advice the part was easy to find and easy to replace once I got the screen off it came right out with a twist. and right back in reverse order, I fired it up and it drained, yay! no more stinky mess and no call to the appliance repair guy,

i unscrewed the 4 screws in the back, took off the guard thing, and unscrewed the existing part with my hand. put new part in and ran dishwasher. the part did not fix the problem, now i'm on to maybe replacing solenoid? i have no idea. this part was simple to replace though. hope i can fix this issue, i need my dishwasher to run right!

remove the four screws in the back of dishwasher on the inside. Remove screen. Remove the piston nut assembly for the check valve. Re-install the screen and four nuts and your done.

I put on my rubber gloves, removed the lower wash rack, removed four screws from the drain guard. I unscrewed the defective part, installed the new assembly and hand tightened. Replaced the cover and installed the screws removed earlier. Re installed the lower tray, and ran the rinse and drain cycle. It has been working beautifully ever since.