66513093N413 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- rich from boulder city, NV
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
heater showing signs that it was going to fail soon
removed unit from cabinet disconnected water and drain lines replaced heater very easy to do it took more time to remove unit from under counter than replace heater piece of cake..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from SICKLERVILLE, NJ
- Parts Used:
- 4317824
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from BOULDER, CO
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher was not drying the dishes.
I followed installation instructions from this site and all went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Jupiter, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Heating element went out, dishwasher wouldn't work
I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- al from Fuquay Varina, NC
- Parts Used:
- WP8565925
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Dishwasher circulation pump malfunction
Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deb from LAWTON, MI
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
front track stop broke on both sides of the upper tray
Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vivienne from GILLETT, PA
- Parts Used:
- W10849471
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Arm sprayer had broken
Something had been loaded in the dishwasher that had gone thru the basket - it hit the arm sprayer and broke it off.
Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.
I watched a you tube video which was referred by part select. This was helpful.
I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..
It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.
Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.
I watched a you tube video which was referred by part select. This was helpful.
I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..
It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WILLARD, OH
- Parts Used:
- W11498831
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old door gasket was leaking.
Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from PEMBROKE PNES, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rail stop clip broke
Very easy to remove the broken one and just clip in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from LYMAN, ME
- Parts Used:
- WPW10463906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old filter was warped, allowing food into the sprayer system
Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SUFFOLK, VA
- Parts Used:
- W11498831
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The gasket listed on your website is to thick. So after installation the door would close. I put the old gasket back in the door closed. However, the dishwasher still leaks soap after a cycle..
As stated above the repair did not go well because the gasket was too wide and the door would close. Suggest you talk with Whirlpool about the part they sold you for my model of dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Groton, NY
- Parts Used:
- W11175771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Stripped the fill valve when installing
I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix from MELBOURNE, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Timer repairs
Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.
Thanks you.
Was this instruction helpful to you?
Thank you for voting!