66513092N413 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Leo from VAIL, IA
- Parts Used:
- W11844992
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Coating was worn and rack was rusting and coming apart.
Polled old rack out, removed water cone from old rack with quarter counter clockwise turn. Install cone in new rack. Slide new rack in washer. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deb from LAWTON, MI
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
front track stop broke on both sides of the upper tray
Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WILLARD, OH
- Parts Used:
- W11768590
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old door gasket was leaking.
Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SAMUEL W from SARASOTA, FL
- Parts Used:
- W11768590
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Leak around door
Pulled out old gasket, pressed in new starting middle top. No more leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Beaver Falls, PA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Drain pump malfunction/melting
My dishwasher wasn't completing cycles and would start to smell like burning plastic randomly. I determined it wasn't coming from inside the tub but underneath the unit. I replaced the drain pump and the drain hose as a precaution to make sure the check valve inside wasn't getting stuck closed forcing the pump to not be able to drain. It was a very easy repair that just involved taking the dishwasher out of the cabinet and turning it on its side. The old pump just twists out and the new one goes in just as easy no tools required. The video instructions on the product page here were very helpful. The hose connects with a clamp and is routed on the side with some plastic clips. It was very easy and completely solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ken from saint simons island, GA
- Parts Used:
- W10872845, WPW10463906
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filters needed replaced
Unscrew top filter, pry off bottom filter, replace with two new filters
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from ELBERFELD, IN
- Parts Used:
- WPW10491331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door leaking and dishes not getting clean
Remove and replace by hand, no tools required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Groton, NY
- Parts Used:
- W11175771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Stripped the fill valve when installing
I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix from MELBOURNE, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Timer repairs
Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.
Thanks you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from SHORELINE, WA
- Parts Used:
- W11175771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dishwasher stopped filling
based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from BOULDER, CO
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher was not drying the dishes.
I followed installation instructions from this site and all went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SUFFOLK, VA
- Parts Used:
- W11768590
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The gasket listed on your website is to thick. So after installation the door would close. I put the old gasket back in the door closed. However, the dishwasher still leaks soap after a cycle..
As stated above the repair did not go well because the gasket was too wide and the door would close. Suggest you talk with Whirlpool about the part they sold you for my model of dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- al from Fuquay Varina, NC
- Parts Used:
- WP8565925
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Dishwasher circulation pump malfunction
Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from flemington, NJ
- Parts Used:
- W11768590
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher leaking
Watched video, removed the door gasket and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lena from Napoleonville, LA
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Leak in hose
Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.
Was this instruction helpful to you?
Thank you for voting!