66512793K312 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Colin from Goffstown, NH
- Parts Used:
- WPW10653840
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door latch wouldn't close
Turned off power to the dishwasher. Removed the front panel via the screws on the inner wall of the door. Lifted and pulled out the front panel. Disconnected cable connections to fully remove the front panel. Pressed down on the latches to the left and right side of the door latch. Pulled out the door latch. Put in new door latch until it clicked into place. Reattached cable connections. Put the front panel back on with the screws. Turned back on power to the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominic from AURORA, IL
- Parts Used:
- WPW10195417
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheels would not stay on
I took the old wheel assembly off and snapped the new wheel assembly on. It’s that simple. Note the dishwasher rack needs to be empty. Very pleased with this site. Parts came super fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Great Falls, MT
- Parts Used:
- WP3400918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
two retainers broke and the main part fell apart
pushed the new retainers in the holes and we are set to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J Kevin from Pittsburg, CA
- Parts Used:
- W10728159
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rack tines were corroded
Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from ELGIN, IL
- Parts Used:
- W10864081
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Leaking door seal
Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.
Was this instruction helpful to you?
Thank you for voting!
Door balance cord failed
Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward F from CINCINNATI, OH
- Parts Used:
- W10872845
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dishwasher would not drain
After bailing out the unit, filled filter hole with a moderate amount of Dawn dish washing detergent. Ran dishwasher twice to remove all Dawn from the unit. Had to bailout the water (and suds) from the washer both times. After the dishwasher finally drained I inserted the new filter..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Mckinney, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Door link broke at plastic connection end
First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from NAUGATUCK, CT
- Parts Used:
- W11177741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
water leak during wash cycle
I followed the video on the site and it worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from NAPLES, FL
- Parts Used:
- W11259786
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Easy repair
Had to remove 2 screws fastening dishwasher to counter. Also removed bottom faceplate to expose the legs and to be able to lower them. Other sites recommended disconnecting the drain and water line but I did not have to do that, I had enough slack in the lines. I got the dishwasher about halfway out of the cabinet and then was able to remove the 4 screws holding the right track. Put the new track in and was good to go. Problem was that the left track broke and fell off a few days later. Still was an easy fix and thanks to PartSelect it was not very expensive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl von der from HUNTINGTN BCH, CA
- Parts Used:
- W10728160
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tine Row Rusted
At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eladio from LOGAN, OH
- Parts Used:
- WPW10538166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley P from ALBANY, NY
- Parts Used:
- WPW10195417
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Not sure
My Husband did it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from AUSTIN, TX
- Parts Used:
- WPW10524921
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Model number issue
When we ordered the part the first time, we pulled the model number from the documentation instead of the machine. We got the wrong part the first time. The people at Parts Select were very knowledgeable and helpful when we called. After we pulled the model number from the machine, they sent the perfect part that popped in with no problems.
Was this instruction helpful to you?
Thank you for voting!
Dish rack slide arms losing ball bearings
Unscrewed mounting screws, pulled dishwasher out halfway, replaced arms, 4 screws each side .....very simple 30 min tops. Parts perfect and quick delivery!
Was this instruction helpful to you?
Thank you for voting!