65715755791 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Hendersonville, NC
- Parts Used:
- 676413
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Latch on soap dish was broken and needed to be replaced
The video was of great help. One area that gave me grief was placing the small part with points under the plastic mechanism in the door. I tried to push the points into the open slot. After watching the movie a few more times I was trying to put the part in backwards. A little more explanation at this point in the video would have been a tremendous help. Otherwise, thank you for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from Rogersville, MO
- Parts Used:
- W10844024
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The old valve has a small leak
Made sure the power and water were not connected to the dishwasher. Removed the bottom panel. Unhooked the old part. Put some plumber's tape around the threads, hooked it all back up. Runs just as good.
Was this instruction helpful to you?
Thank you for voting!
There were no provided instructions, just had to wing it.
Trial and error. The spring was difficult to install, the pin and door were easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Fort Oaks, NC
- Parts Used:
- WP661566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Machine would shut down during the wash cycle.
I read information on this website about the function of the high limit thermostat. I found that it was the problem by disconnecting the two wires on the thermostat and straight wiring to bypass it. This allowed the machine to work properly so I ordered the high limit thermostat. To replace the part I used a screwdriver to remove the instrument panel and replaced the high limit thermostat by disconnecting the two wires from the old thermostat and connecting the wires to the new thermostat. I then replaced the instrument panel. My machine is working properly again..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matt from grant park, IL
- Parts Used:
- 676413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dish washer soap drawer would not work
we followed your instructions submitted via e-mail and they worked out just fine....thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl F from liberty, TN
- Parts Used:
- WPW10204131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
top basket wheels worn out
used a common screw driver. took the ends off then pulled out the basket . used the screw driver to pop the brackets with wheels attached. new ones back on and about twenty minutes done. very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Bellerose Manor, NY
- Parts Used:
- WP661566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
High limit thermosat blowes when on santi. rinse
Remove blown high limit therm.and replace with the new high limit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Taylor, TX
- Parts Used:
- W11086533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Unfortunately, a mouse had made its home on top of our surround insulation. For hygienic reasons, I replaced the surround.
1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Little Rock, AR
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Top of the Soap Cap Latch was broken
The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrel from rosamond, CA
- Parts Used:
- WP8066018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lid Spring
Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Westchester, IL
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher seals leaking
The repair man from a serve we use, look up on how to replace the door gasket. Washing hands, do not stretch, and tap rubber into place. No more leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruby from Saint Marys, GA
- Parts Used:
- 675238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
missing part
screw it in then hook up the hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Fort Worth, TX
- Parts Used:
- WPW10204131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Wheels on top rack broke
Watched online video and followed instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Waukesha, WI
- Parts Used:
- WPW10082896
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Old Heat Element Started smoking
Everything was very easy ordering and replacing the heat element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Rehoboth, MA
- Parts Used:
- 676413
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch worn out
Followed vidio instructionson web site. Quick easy fix
Was this instruction helpful to you?
Thank you for voting!