19495 ((1988)) Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The door spring broke in half on the front door of a twenty two year old Maytag dishwasher
Easy repair, I put small marks under the counter to make sure the dishwasher went back in the same spot for easy screwing back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Becky from Stanley, NC
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
The Faucet Adapter was worn out.
Ordered a new Faucet Adapter! Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Silver Spring, MD
- Parts Used:
- Y901862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door spring broken
once i got it out the spring was a breeze
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norm from Hamilton Square, NJ
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
A gift portable dishwasher did not have the faucet adapter.
Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from CONNEAUT, OH
- Parts Used:
- 6-9021150
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Broken Belt
After discovering the broken belt. 2 Days later I had the new belt from partselect. I placed the belt on the motor pulley then after 3-4 attempts was able to get the belt on the other pulley. It will go on. Comments from other customers really helped. After you get belt on then apply lub, per instructions. My maytag is over 20 years old still works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Avon, MN
- Parts Used:
- 6-9021150
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The dishwasher did not drain
"The order arrived in relatively short order. However, the installation must have been hilarious to any observer. Imagiine an arthritic septuagenerian getting down on the floor and wallowing about fitting a dish washer belt. Hints: 1. Grasp the pulley on the pump with your left hand from under the discharge hose (more room than over the hose) when fitting the belt to the rear of that pulley. 2. Use a hot pad (not an emroidered & quilted one reserved for company) to protect your L forearm from the frame member on the bottom of the machine. Getting up was worse than getting down, but it works! In dishwasher years it's much older than I am."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from SLIDELL, LA
- Parts Used:
- WP901403
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
water leaking at door of dishwasher
based on instructions from previous customers, took off front control and door panel, removed old gasket, replaced new gasket by aligning tabs and pulling through with needle nose pliers, leaking stopped
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Slidell, LA
- Parts Used:
- 6-9021150
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Motor running but no motion or pumping action
Removed the kick plates to access the pulley system, Heated the clear belt in hot water and installed it by rotating the large pulley to stretch the belt on. Then added the lubricant to the belt. Reinstalled the kick plates with nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Los Alamos, NM
- Parts Used:
- 6-9021150
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Belt to stiff to roll onto pulley
150 degrees for ten minutes provided enough flexibility to allow the belt to be rolled around the pulley. The machine has been used successfully since installation.
Was this instruction helpful to you?
Thank you for voting!