18885 ((1988)) Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Harry from Franklin, TN
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rinse Aid Fill Cap missing from dishwasher in condo I just bought.
Opened package, removed cap and screwed it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Perry from LaFontaine, IN
- Parts Used:
- WD8X181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Leaking Drain Valve Shaft Seal
I took the lower cover pannel screws out of the dish washer to view the pump assy. Then remove the solinoid bracket which covered the Drain Valve Seal. The hardest part was removing the star washer in front of the seal. That is where I had to use the pliers to remove it. Then I had to straighten
the washer out so I could reuse it. Pulled old Seal out and replaced with new and reassembled. Test ran a cycle and wasn't leaking any more. Easy fix!
the washer out so I could reuse it. Pulled old Seal out and replaced with new and reassembled. Test ran a cycle and wasn't leaking any more. Easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Pembroke Pines, FL
- Parts Used:
- WD16X10011
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Could not get the arm to close.
I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.
Thanks for your help.
Thanks for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHNNY from ASHLAND, VA
- Parts Used:
- WD8X181
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
leaking shaft seal
Well disassembly was good - removed the spring cam assembly on the dump valve cam, then two screws of the solenoid to remove the solenoid, beyond that the repair became a little tough since the seal / shaft retainer wasdifficult to remove. The shaft has a grove which the retainer clip is hard to remove from, and once removed - it deformed, so i installed the seal using a nut driver as a seal press to evenly press it into place. then had to work the retainer with a small set of pliers to reshape it, then reaasembled in place which is when i realized why it was hard to get off due to the shaft grove, which as well as holds the seal it also aligns the shaft latteraly in the pump housing, but after putting it all together and firing up the dishwasher, no leaks and it was an hour laying on my side which i feel was worth it, thx jon
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sebrana from Tompkinsville, KY
- Parts Used:
- WD19X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
dishwasher was filling up .but it was,nt washing .had a repair man looked at it and said it needed a seal .so we bought it and install it our self and .it wasn,t that it was the moter .instead of a seal .
took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Cloverdale, IN
- Parts Used:
- WD8X181
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
dishwasher leaking
Pulled the dishwasher out and turned on its back and pulled out the seal. Saw it was bad and order one. It was here in two days and fixed that afternoon. Great service and quick delivery!!! Will use this site again!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rick from greensboro, GA
- Parts Used:
- WD19X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
slow leak from the pump while operating
followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which was not present on my original however it installed perfectly and no longer leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Northville, MI
- Parts Used:
- R0913111
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Pump seal elak
Removed motor and found shaft severely rusted. Cleaned up the rust but the shaft was too pitted to work effectively with the new seal.Wasted my time and money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from CLARKSBURG, NJ
- Parts Used:
- WD8X181
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking, not cleaning
Followed the directions. I've done this before. I used to fix these things for a living. The metal clip in front of the seal wouldn't come off. I ended up pulling the shaft out of the drain flapper in the pump which ruins the pump. A 14 year old DW isn't worth a pump. So I bought a new KitchenAid. The seal should come with a new metal clip since you may have to destroy it to replace the seal. If you are buying a seal, buy the clip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Willcox, AZ
- Parts Used:
- WD19X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaking motor seal
Followed easy instructions and completed repair in less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Chicago, IL
- Parts Used:
- WD13X71
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would run for short time and the stop
Most difficult part of repair was determining that latch was the problem. Originally believed it may have been the float on close inspection could find nothing wrong with it. After realizing that a small amount of pressure on the latch would keep the washer running, the culprit was identified. Appreciated ease of finding replacement on PartSelect. Ordered item on Sunday night and it was delivered Tuesday via normal service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Corvallis, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid fill cap broke off at base
I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Lake Bluff, IL
- Parts Used:
- WD19X10032
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher leaked badly when running
At first, I found a metal band that was rusted and loose, replaced it but still had a leak. I went to the diagnosis section and identified another area of problem, ordered the part and got super quick delivery. With the help my wife I was able to pull apart, repair and get the unit to run and stay dry. Wife is happy because she loves the décor of our old but now dry dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Mechanicville, NY
- Parts Used:
- WD19X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Pump was leaking from the shaft seal
Removed and inverted the DW. Removed the impeller, grinder, screen and seals then the actual shaft seal. Replaced with new parts in reverse order. Instructions provided with the seal kit were simple and excellent. They were right to the point.
Was this instruction helpful to you?
Thank you for voting!