66515897990 Kenmore Dishwasher - Instructions

Followed instructions as the videos on this page show.

I guess some food got caught in the water level sense float and caused it to mal function.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.

Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!

I needed a #3 screwdriver. Cut the top of the ring of the tube holder, one snip from a pair of side cutters. Unscrew the old tube, screw in the new one, the old tube holder works fine with the cut in it . I didn't need to remove the top rack. Done.

I went back to the web site to make sure I'd ordered the right part.?? looked at the diagram and then watched your little video.?? He had the part hooked opposite of what was shown. (The arm wouldn't rotate) So I turned it arround. While he was still??. It took me less that 5 min and the dishwasher is working Great.????

required NO tools,

just unscrew the large thumb screw, and replace the washer arm bearing!

problem solved like that!

maybe a 5 min job. part was a perfect match.

First, I removed the tines which were still connected to the top rack by the unbroken parts of 3 clips. (The part of the clip which is subject to breakage is the top, where it allows the tines to be clipped up or released and laid down.) I left the broken clips on the rack as a guide to where to install the new ones. I then attached the new clips to the tines, which is like assembling a puzzle. It would be helpful to replace one clip before all 3 break, so you have an illustration, but it's fairly easy to figure out how to attach the clip as long as you realize the tines need to be released and folded down, or clipped in the up position. With all 3 clips attached to the tines, simply pop the broken clips off the rack and attach the tines to the rack with the new clips. I appreciate the advice from the users who warned against breaking the clips with a tool. It's not really necessary to soak them in hot water. My advice is to use only fingers for installation. Brute force is not necessary... just position and pinch.

The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!

I put the bearing ring on the washer arm and then screwed on the retainer nut.
Easy to order the needed parts

The new part was one piece and merely took unscrewing the holder and replace the part. Except for the screw being tough to remove, putting it back on was a snap!

Removed broker washer arm mount with screwdriver and replaced. New parts clipped right on to upper rack, no tools needed. Didn't really need to replace the tube holder but it was brittle so I put it in the order.

Screwed on a new one. The real story is getting the part. I called about noon one day and the part was dropped off at my house by FedEx the next day. Unbelievable. And the lady I talked to found the part number etc that I needed in a few minutes. Great service at a fair price.

The nut had broken off even with the top of the threaded area, so we had to remove that broken part. We did so by using small pliers and inserting them in the opening and held them in a spreaded position while turning the broken piece out. We replaced the three new parts and put it back together and it works fine. So easy and much cheaper that having a repairman come in. Took us less than 15 minutes.

This spinner is attached to a plastic module PN WP3379369 which is held in place by two screws to the top of the dishwasher. I was able to temporarily reattach the spinner by using a hot soldering iron to melt the nylon axle that goes through the spinner. By using a very small metal washer placed on top of the spinner I was able to melt enough off the end of the nylon axle so as to keep the spinner in place and still be able to rotate. By far the most difficult part of this repair is removing the two stops that prevent the upper washer rack being removed from the machine. Doing so requires using a pair of long nosed pliers and taking note of what needs to be squeezed. Even if installing a new part the upper rack needs to be removed in order to get access to this central part.

Easily installed the hose and replaced the middle spray arm with the help of my brother the savior! Lol. It was very easy for him to install.