66515825690 Kenmore Dishwasher - Instructions

Nozzle cap rubber housing was split and cracked. It simply unscrews. The replacement was a matter of screwing the new nozzle cap on. My wife was trusted with this installation. Believe me, this indicates how easy it was.

We read your help site and was able to find what was causing our water filling probelms. Order the valve intake part and made the repair and the dishwasher works like new. You saved us a repair bill from the professionals and they couldn,t done a better job. I will recommand to site to everyone. Thanks Again

I replaced the seals per the video instructions.

So my dishwasher is 20 some years old. Woke up in the morning to smell burning plastic and the dishwasher never moving to the next part in the cycle. I thought it was the high limit, then the cycling thermostat(because cycling you'd think it was cycling wrong). Nope. It was working fine. I used a multimeter to test the high limit(ohm reading will be closed at room temp) and for the cycling(will be open at room temp, so use a multimeter with alligator clips and a lighter to trigger it to close). All of my existing parts were fine. So I went to the timer and tested with alligator clips, each part that connected during the timing cycle. Sure enough. On the rinse and pump water out part, the contact point wasnt connecting due to corrosion and a bent prong. So I rebent it and cleaned all the contact points. All you need to do on these old washers is pull out the timer and pull off the thin plastic "sheild" over the thing. Guess what. I have a working dishwasher after having done the impossible and fixed my timer. So for those who have a dish washer that won't advance, but you can hear your timer advancing with the clicks, this is your problem. Saved myself an unknown amount of money because they don't make my timer anymore.

Both springs (8066018 and 3368999) were replaced as recommended in your troubleshooting guide, but did not resolve the problem. Finally the Dual Motor, 3374501, was replaced. During the above, the plastic face of the door fell off, which created a nuisance task before proceeding to fix the original problem. However, while replacing the motor, I realized the purpose of the two, T-shaped studs sticking out of the motor. It is absolutely necessary that these sit inside the slots which engages the sliding plastic cover, which is spring loaded, in order to engage the release of the soap dispenser door. It was truly a learning experience, but I got it done.

It took all of 30 minutes from beginning to end remove the old parts and replaced them and run a diagnostic test before I could wash dishes. The parts were exact and Parts Select has always provided the right parts, shipped fast and never disappointed me.

Part arrived in 48 hours. Had to pry apart the two piece assembly of the damaged item. Snapped the replacement in place and fastened it to chassis with two machine screws

I searched for the 18x5x5 insulation.,ordered it from Part Select. Waited. Company sent wrong part. Called, they gave me a refund, reordered, promised 2 day free shipping. Waited more than a week, paid for 2 day shipping. Received same, wrong part. Still don't have repair done. Looking elsewhere for part.

After cleaning the filter located on top left of door(used a screw driver to pry out) and following the install gasket video problem solved.

Ordered part, recieved part package, opened package, inserted screw cap rinse aid tank cover, twisted to close. Job completed. Time required about 15 seconds from opening package. Service was excellent and accurate. Thank you.

Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.

Just replaced it in the notches that held the rusted tine.

The old tines on the lower tray were easily removed by bending them in the middle and pulling the ends out of the holders. The replacement tines went in just as easily. The old door seal was pulled out by hand and the new seal was pressed in easily with just using fingers.

I was most impressed with the communication in regards to product backorder. They gave me an estimate of product availability and an option to change the order. Great customer service!

quick and easy,tine-row just snapped right in! Took about 15 seconds!

Pulled out the old with needle nose pliers. Pushed in new door seal with fingers.