Models > 66512776K311 > Instructions

66512776K311 Kenmore Dishwasher - Instructions

Jump to:

All Instructions for the 66512776K311
91 - 105 of 398
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Leslie from AUSTIN, TX
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
door would fall or slam open, no tension to hold door open.
Unscrewed mounting screw at top and bottom of duahwasher, pulled out dishwasher could see the pully on one side had broken. installed new part put dishwasher back in place and rescrewed mounting screws.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from Drexel Hill, PA
Parts Used:
W11177741
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Original door seal came out while emptying dishwaher. It was pretty messy so i ordered a new one.
I just followed the directions on the video that was part of the pictures for the door seal. I made sure that the channel was clean and the new seal pressed right in. i wish I had checked this site before I called a repairman, who wanted to charge me over $400 for a new one.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from ELGIN, IL
Parts Used:
8194001
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Squeaky dishwasher door
Just like the video; remove the 2 nuts off the kick plate, remove the 2 screws under the counter, pull the unit out, ease the spring off the cable, nut drive the pully assembly's off, install the new ones, place new rope/cable from the door arms onto pullys, attach the spring, push the unit back into place, replace screws and the kick plate. Took 15 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from WEST NEWFIELD, ME
Parts Used:
8194001
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
spring cable end broke
followed your very well done video clip exactly.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from LONGVIEW, TX
Parts Used:
8194001
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The dishwasher door wouldn't hold in any position but went all of the way open.
You said the repair was easy and would take around 5 minutes to perform. You were spot on and the instructional video really helped do the job.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JIMMY from ST GEORGE ISL, FL
Parts Used:
8194001
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
cord on balance mechanism broke.
pulled it out, saw 'pulley' was fine, and put cord on spring and puled it enough to hook it on other end.end after running cord around the 2 pulleys, as it was on the other side. push it back and done.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lawrence from COGAN STATION, PA
Parts Used:
8194001
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Door would just fall open
Followed directions here. Extremely easy repair.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Florence, MT
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
The right hand nylon link broke & the door would fall open with the spring tension gone
remove the bottom plate with a nut driver and back off on the front leg adjusters. Slide out the dishwasher approx 8-10 inches and remove the broken link. The new one goes on easily. Look at the opposite side if in doubt as to how to attach. Slide the unit back in and tighten the leg adjusters until the unit is secure. reattach the lower front panel which hides the leg adjusters, etc. You're done!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Beaver Falls, PA
Parts Used:
8269144A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Drain pump malfunction/melting
My dishwasher wasn't completing cycles and would start to smell like burning plastic randomly. I determined it wasn't coming from inside the tub but underneath the unit. I replaced the drain pump and the drain hose as a precaution to make sure the check valve inside wasn't getting stuck closed forcing the pump to not be able to drain. It was a very easy repair that just involved taking the dishwasher out of the cabinet and turning it on its side. The old pump just twists out and the new one goes in just as easy no tools required. The video instructions on the product page here were very helpful. The hose connects with a clamp and is routed on the side with some plastic clips. It was very easy and completely solved the problem!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sandra from METHUEN, MA
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Door became heavy on one side
Pulled dishwasher and removed existing springs and attached rope. Ordered the part needed and replaced it somewhat easily. There is a lot of tension because of the spring on the door. Once part was installed we were ready to use our dishwasher right away. Even though the rope was broke on only one side - we replaced both sides.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Falls Curch, VA
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Door would not stay up unless closed - broken door spring
Pulled out dishwasher to access the sides. Removed onld lines and then unscrewed pulley from frame using socket / nutdriver. Replaced pulleys with new units supplied in the kit and then threaded new lines onto door and springs. Repair complete in less than 5 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Hohenwald, TN
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
One tension line broke.
I pulled the dishwasher out just over half way to access the spring area. Unscrewed the old assembly and screwed the new one in it's place. Attached the string line to the spring, wrapped it around the assembly and attached it to the door hook. Repeated procedure on other side. Problem solved.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeffrey from Petaluma, CA
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
No spring tension to dishwasher door.
After pulling the dishwasher out of the cabinet (2 screws held brackets to the underside of the counter - accessible when the door is open), I removed the broken link pieces, re-attached the springs and routed the link line around the pulleys. No need to re-set the spring tension as it was adjusted properly.

Was able to download a PDF manual from Sears for the dishwasher, so had the necessary information in the event adjustments were necessary.

I bought spare links as the dishwasher was less than 3 years old, and I expect them to fail again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sophie from Brooklyn, NY
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Door got very heavy and wouldn't support itself
Removed 2 screws that held unit under counter. Slid diswasher out about half way; reattached metal spring in back and removed broken string. Attached replacement string to spring and threaded through wheels (copying other side), then attached string to door. Tada! Done. Will never pay a call-out fee again (for this problem anyway...)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Andrew from Mansfield, TX
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Door pulley rope broke
Turned off power to dishwasher.
Removed screws from dishwasher retaining clips.
Pulled out dishwasher.
Removed broken rope.
Installed replacement and put everything back together.
Very easy repair. The spring is very strong and extra hand can be helpful, but not required.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 66512776K311
91 - 105 of 398