66213289K112 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lucille from MODESTO, CA
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Washer would not turn on
Watched a video and read through written directions.
Did not need to pull out the dishwasher from the cabinet.
Did not need to pull out the dishwasher from the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from DREXEL HILL, PA
- Parts Used:
- W10619006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Top rack adjusters fell apart and would not slide back and forth.
I followed the Partselect video for the new installation. Very easy to follow which made new part installation extremely easy. Works perfect now!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from VANCOUVER, WA
- Parts Used:
- W10300781
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No lights not working.
Replaced control module and then replaced touch sensors.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from STATEN ISLAND, NY
- Parts Used:
- W10619006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door would not lock
Followed the u tube video. No problems. Will use them again.
Best recommendation I can give.
Best recommendation I can give.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from ALBANY, GA
- Parts Used:
- W10619006
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
door would not latch
We followed the video instructions, at times running to the computer to check the video.. The hardest part was getting the door to slide back on.. Thank heavens for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from WOODBURY, NJ
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When the door was in the closed position there was no power to the unit. The control panel buttons would not put the dishwasher in any cycle. the panel lights did not work.her
I first verified that there was 120 volt line voltage getting to the unit. I removed the outer door panel by removing the 10 torx screws located around the panel on the tub side of the door. Two of the screws are longer so note there location for reassembly. The door handle can now be removed. Pull the outer door panel away from the inner panel and remove the connector to the control board. Set the outer door aside. Remove the connector to the door latch.The latch is snapped in position at the top side. Pry using a screw driver to release. Snap new latch in position. Snap on connector, Reassemble door by first reconnecting the control panel connector. install plastic door handle. Mate door to inner panel. Note interlock tabs between outer door and inner panel near the bottom area. Install the 10 screws. The two longer screws are at the top holding the latch and handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Abby from SACO, ME
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Door would no longer latch
cut power to dishwasher. removed screws all around door panel to get front panel off, leaving top two screws for last. unplugged latch set, removed it. set new one in. screwed top 2 screws in. fit door panel back on. pulled out latch hook from stationary top piece and clicked new on in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from SANDY, UT
- Parts Used:
- W10619006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Dishwaster would not reliably start. Just blue flashing light
Removing the door was straightforward. However, when the door panel was removed, I grabbed the door and my finger touched and pressed on something on the right side. This is an optical collector which focuses 3 lights (red, blue, green) into a visible slot. After I reinstalled the door, the lights were not visible. I had to disassemble the door a few times and bend this optical collector into the right position. Basically, I bent the collector into the door, so I needed to bend the collector away from the door. And now, everything is fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from escondido, CA
- Parts Used:
- W10619006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch broke on dishwasher door
I removed the screws on the inside of the door. Removed panel from the outside. Disconnected the power wires to the panel. Disconnected the wires to the latch switch. Removed the latch assebly. Put new assembly in place. Connected swtich wire. Connected panel wire. Put panel back on dishwasher door. Installed panel retaining screws. Job Complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from Holbrook, NY
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door lost the tension
Installed the rubber grommet and the door was fixed.Wish the product was made to lasts,second time in three years the part had to be replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phil from santa rosa valey, CA
- Parts Used:
- W10619006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Kitchenaid Dishwasher Wouldn't Turn On
Replaced latch switch with parts-select whirlpool (usa) model (good choice) and unit still wouldn't turn on. I then turned 115 vac power off to unit for 1 minute and then back on and unit worked correctly with no additional problems. .
Was this instruction helpful to you?
Thank you for voting!