JDB2150AWP0 Jenn-Air Dishwasher - Instructions

Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.

The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.

Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.

The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.

I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.

Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!

first, i removed the inner door panel exposing the latch assembly. i then disconnected the wiring to switches noting their locations. removed and replaced with new latch assembly, connected all wiring back to their corresponding switches, assembled the inner door panel and checked to make sure the latch was working properly.

Ensure to order part # PS1559543, which is the complete assembly although the diagram doesn't show this, and not PS2100626 which doesn't include the handle. The new assembly is a different style than the original therefore you should replace the complete assembly.

This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.

First, shut off the circuit that the dishwasher is on. Remove the 10 - 12 screws that secures the inside waterproof panel to the door. There are two electrical connections are either side of the handle (latch assembly) that need to be removed. No need to disconnect any other connections or reservoirs. The handle comes right out. Seat the new one in door front opening. Reconnect the electrical leads and reseat the interior panel. I would put in the 2 screws are either side of the handle first; then the 2 at the bottom on either side and then the remaining. This is a very easy DIY job.

After receiving the latch assembly, which arrived rather quickly, I found the handle itself was not enclosed in the package. Therefore this repair was delayed and after several calls to the 1-800 number I was informed the company had discontinued the distrubution of the handle. They offered a full refund, however I'm still waiting for the return labels so as to ship the latch back.

Now on the brighter side, the company representative put me in touch with a local distributor that did carry the latch/handle assembly as one piece and for a lot less money.

For those who are attempting the repair, don't worry, It was very simple. Just remove hex screws, lift the inside panel, unplug the two connectors and insert the new assemply.

Must say my wife was very happy to have the dishwasher up and running again.

Good luck !

When the (overpriced) replacement silverware basket arrived (rapidly, within a few days of my ordering) I was shocked and angry that the handle for the basket was not included--nor were instructions included as to how to remove the old handle from the old basket in order to fasten it to the new basket. Therefore, I spent a considerable amount of time trying to pry the handle off the old one, which was quite tricky: There were four slots which held the plastic "catches", and they had to be pushed out simultaneously. I had to fiddle with it for at least a half hour, trying various implements, until I found that I could push them out simultaneously by wedging butter knives into the slots and then easing the handle off. (I was careful to position myself so that I wouldn't slip and stab myself with the blunt butter knife.) After that, the handle snapped fairly easily into the new basket's slots.
In the end, while I was glad to be able to recycle the old handle, I wish that the basket and shelves were made more durably so they wouldn't have to be replaced, or that they could be replaced at a more reasonable price.

I'm telling this story for my husband who is a pretty handy guy--I watched him do the repair. I had had someone out to look at the dishwasher and they said it would be $284 to fix this one little thing because you couldn't buy the one little part separately, you had to buy a whole new motor. Since the dishwasher is old, it didn't make sense to invest this much in it--might as well buy a new one for that kind of money. My husband did some looking around and found the part on your site and installed it himself. So the cost was under $40. The dishwasher is now working better than it had been for a while.

seeing as how my husband was out of town, I inserted a regular flatware knife in each of the four slots that held the handle in place on the basket. I then slowly pushed down on the handles of the knives on opposite sides of each other to unlock the handle from two slots on the basket and then went on to push down on the other two flatware knives on the opposite sides...sure enough, the handle came right off...less than 5 minutes in all to take the old handle off from the old basket and then snap it into place onto my newly acquired basket.

I removed the screws around the top and halfway down the sides of the inside of the door. I found that you dont have to remove all 10 screws to access the assembly. Reach in and pulled out the assembly, there was enough slack to pull it out above the door. Pull the connectors off and slide the new ones on. Set the new assembly back in place, insert the 2 top screws first, and then the rest. That was it...very simple to change.

Replacement basket did not include handle so needed to pry old handle off broken unit to use on the new one. Used screw driver to pop loose clips which attached to basket. Had to stick tooth picks broken in half under them to hold out until all four clips were opened at once - then handle could be pulled off. Easily snapped it back on to the new basket and repair was done. Can't get any easier than this!