JDB3650AWF2 Jenn-Air Dishwasher - Instructions

I ordered part PS10064063, metal left and right rack adjusters that should be more durable than the plastic parts that broke. To install, I watched this YouTube video (https://www.youtube.com/watch?v=otUn8eoceBw), pausing and rewinding as needed. Piece of cake! FYI, when the axle broke, the small little plastic prongs stopped the grinder, which caused the dishwasher not to cycle. Fortunately, that was repaired under extended warranty, but the rack wheel was not covered. The repairman said the grinder (in most dishwashers these days) is a very delicate blade. They can't really grind much - even tiny plastic pieces.

After doing some research on the Kitchen Aid issues. I turned off the breaker. Remove the (6) #15 Torx bit screws from the inside upper panel and removed the outside control panel. I located the Bi-Metal Fuse. I turned the breaker back on.Took a Electric Meter and it showed power only on one side. I order the part (BI-Metal Fuse) from the company. Turned the breaker off to there dishwasher. Very easy to install. I cut and trim the (2) wires. Match the black wire with the white stripe to the exact same color code and do the same for the all black wire. Install one wire at a time and tighten down with a small pocket screw driver. Then use the plastic tie straps to secure the (Bi-Metal Fuse).Turn the breaker back on. You are good to go.

The manual that came along was confusing and was bit frustrating. I did not know how to remove the old parts. Then I viewed the video on YouTube. It was a lifesaver. I would recommend to viewers this video and it was like a piece of cake It took not more than 15 minutes including watching the video.

I ordered this thinking I would probably need more parts, but was unsure which ones. When the part arrived I immediately noticed that it was not identical to the original part, but looked like it may work. I also received an instruction book that I did not expect. The first side probably took 15 or more minutes. The second side was installed in just a couple minutes. The toughest part was removing the old pieces.

Pulled up old spray arm and snapped new on in place. Took less than a minute and no tools. Dishwasher is like new again.

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!

removed front panel and pry switch from latch then remove two wires and reverse to install.

Called and with the help of Brandon in customer service the part was ordered,. It was a simple fix.. just snapped into place. Thanks!!

Followed the repair video supplied by the site

removed and installed cords with screw driver

lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.

After replacing the door seal and the dishwasher still leaked a lot of water out the bottom of the door, I read posts by a couple of other DIY who said the lower spray arm can split at the seam and cause this. One post noted it is very difficult to determine if this is the problem, that you may have to take the blade of a screwdriver and try to pry the seam apart gently to see if a gap does appear with very little force being applied. If so, then just imagine what happens when that very hot water makes that plastic more flexible and then the seam opens and forces waves of water against the lower door. I could see a small seam split using that strategy and when I replaced the spray arm, my leak stopped. I don't regret replacing the door seal as it had a couple of small tears and hard water deposits all over it, so it was time to do that even though it was not the culprit for the extensive leak. The arm is SO EASY to replace, just twist the plastic nut under it and it pops right off. Put the new one on and twist the nut the other way and it secures it.

The kit didn't come with instructions, so I found the following YouTube video

Laid all the parts out after removing the old adjusting units off of the top rack. I figured out how the new parts went together and attached them to the rack and replaced the rack in the dishwasher. The instructions that came with the new adjuster kit were not much help they were hard to understand and the pictures weren’t very good easier to figure it out on my own. Hope this helps

Parts came with instructions however I just searched the part #on you tube and found a video of someone doing the repair. That made it super easy. Took me only about 20 min for the whole job and I am not a very “handy” guy. So glad I didn’t pay someone to come out to do this. Easy repair! In a nutshell you completely remove the old housing and wheel structure and replace it all with the new parts so when taking off the old parts don’t worry about breaking them.