JDB3600AWP3 Jenn-Air Dishwasher - Instructions

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

really easy to repair... no power to control panel but had power from breaker box. Followed directions that came with part, self explanatory, took 10 mins.

Followed the repair video supplied by the site

After replacing the door seal and the dishwasher still leaked a lot of water out the bottom of the door, I read posts by a couple of other DIY who said the lower spray arm can split at the seam and cause this. One post noted it is very difficult to determine if this is the problem, that you may have to take the blade of a screwdriver and try to pry the seam apart gently to see if a gap does appear with very little force being applied. If so, then just imagine what happens when that very hot water makes that plastic more flexible and then the seam opens and forces waves of water against the lower door. I could see a small seam split using that strategy and when I replaced the spray arm, my leak stopped. I don't regret replacing the door seal as it had a couple of small tears and hard water deposits all over it, so it was time to do that even though it was not the culprit for the extensive leak. The arm is SO EASY to replace, just twist the plastic nut under it and it pops right off. Put the new one on and twist the nut the other way and it secures it.

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

This repair is simple. However, what you recieve is a box of loose parts and no instructions. The new parts are not remotely the same design as the original. You have to figure out how to remove the old parts (fairly easy by careful prying) but then sort out what the new parts do and how they fit together. It takes patience and some mechanical knowledge. Once you figure it out, it goes quickly. A fairly simple diagram included with the parts would be definite benefit for most people. It seemed like an odd omission. They also include the shortest star driver (about 1 inch long) I have ever seen for the 4 screws but it is useless since you can't really apply enough torque to the screws to properly set them. Be prepared with a standard length star driver.

Pulled upper tray out. Removed old adjusters and replaced with new. The pictures in the installation instructions were bad (blurry and hard to distinguish). Had problems with the first side button. Put it in before installing the wheel base on the second side. Went much easier that way. You did need a star tip for the screws.

Removed the old one, cleaned out the groove, dry fit the gasket, made a small cut to fit length, removed, squeezed the glue into the track and then put gasket in. Had to wait 24 hours for glue to cure.
No leaks.

I spent more time reading the easy instructions several times than it took me to actually do the repair to replace the fuse. I wanted to make sure I fully understood the instructions before I undertook the task. I also checked out a video on You-tube which explained and showed me the same thing as the instructions did. By the time I picked up the screwdriver, I was practically "an expert". I just cut two wires and hooked up two new wires and... done. The instructions were simple....so was the repair. Nothing to it.

remover the nut inside of the dishwasher under the float took bottom plate off open the plastic housing installed new the new float switch plug in the wires snip in the new housing put the unit back in the hole put nut back on and put the bottom plate back on easy as pie

Note orientation of the old gasket before removing it, so you can put the new one in right. Pull the old one out, which is a snap. Mark the center of the new one and push the center into the channel with your thumb nail at the top middle of the machine. Continue pushing it in on both sides, from top to bottom, in a steady, fluid motion; don't stretch it. If there is a bit extra at the ends, cut it off with a scissors, being conservative so you don't cut it too short. The new gasket will make the door a bit harder to close, but that's what you want.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

The old filter simply unscrews and the new one screws in.