Models > JDB3600AWX4 > Instructions

JDB3600AWX4 Jenn-Air Dishwasher - Instructions

Jump to:

All Instructions for the JDB3600AWX4
121 - 135 of 899
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dylan from RIVERSIDE, CA
Parts Used:
WPW10348269
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Dishwasher not draining on final cycle and smelled of burning
I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Martha from SAN DIEGO, CA
Parts Used:
W10872845
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Water filter needed replacing
The old filter simply unscrews and the new one screws in.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fredrick from BROADALBIN, NY
Parts Used:
W10648041
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
leaking water inlet valve
I closed the water at the tank and opened all the hot water faucets in the house thereby draining static water from the inlet hose at the valve. Then I unscrewed the inlet hose from the valve, unscrewed the valve body from the support bracket under the tub, unplugged the electrical plug from the valve body, and removed the outlet hose. I installed the new valve using the reverse sequence. Then I closed all the hot water faucets, turned on the hot water at the tank, and purged air from each of the faucets. I then started the dishwasher and ran it through a complete cycle, periodically checking it for leaks, and found none. Total time for uninstall and reinstall - about 30 minutes. Not bad for an 80 year old.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from DALLAS, TX
Parts Used:
W10712394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Upper rack wheel broken
The pictures in the instructions supplied were horrible. I found a video on You Tube that made the install easy
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
michael from WINCHESTER, MA
Parts Used:
8193506
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
leaking water bottom rigth side
remover the nut inside of the dishwasher under the float took bottom plate off open the plastic housing installed new the new float switch plug in the wires snip in the new housing put the unit back in the hole put nut back on and put the bottom plate back on easy as pie
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Andre from Sugar Land, TX
Parts Used:
W11196317
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
New door seal difficult to insert.
The first try didn't go well. The door didn't stay locked because the new seal was preventing it.
I pulled it back off for the second try and first I let it soak in the hot water for a few minutes to soften the rubber. Then I lubricated it with Vaseline and now the seal got in the grove easily and completely. I believe that that step was critical to ensure 100% success rate. After that everything was fine, the door locked properly, and, of course, there was no more leaking.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Keith from PROSPECT HTS, IL
Parts Used:
W10712394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Original upper tray had broken away from all 4 rollers.
Although the b&w photos spooked me a bit. I quickly learned to tear off/break off the old adjuster arms, and then refer to the written directions for installing the new parts. Don't waste your time trying to figure out removal of the original parts, just get them off. So, I did not find the photos helpful, but I figured it out.,with help from the text And of course, once you do one side, the other side is a breeze!
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Mckinney, TX
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Door link broke at plastic connection end
First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Franco from UNIVERSITY PK, FL
Parts Used:
W10712394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Take out old broken parts and install new ones
Followed the instructions from the U Tube video by Matt from Appliance Video for Adjuster Kit W10712394. Matt did an outstanding job describing exactly how to remove the old parts and install the new ones. He speaks slowly and precisely and left no detail behind. Removing and installing the parts went like a breeze! Thank you Matt!
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Perri from NORTH ANDOVER, MA
Parts Used:
W10712394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Broken wheels that guide upper rack
Followed the enclosed direction sheet
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOSEPH from LAMBERTVILLE, NJ
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Door falls when opened
Attached new link, then stretched the spring with pliers and routed link over the pulley. Replaced both links.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
bruce from SMYRNA, DE
Parts Used:
W10712394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The wheels broke and came off of the top rack had to replace the top rack adjusting unit
Laid all the parts out after removing the old adjusting units off of the top rack. I figured out how the new parts went together and attached them to the rack and replaced the rack in the dishwasher. The instructions that came with the new adjuster kit were not much help they were hard to understand and the pictures weren’t very good easier to figure it out on my own. Hope this helps
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from JENKS, OK
Parts Used:
W10712394
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broken wheels and adjuster
Parts came with instructions however I just searched the part #on you tube and found a video of someone doing the repair. That made it super easy. Took me only about 20 min for the whole job and I am not a very “handy” guy. So glad I didn’t pay someone to come out to do this. Easy repair! In a nutshell you completely remove the old housing and wheel structure and replace it all with the new parts so when taking off the old parts don’t worry about breaking them.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jessica from CASTLE SHANN, PA
Parts Used:
W10258275
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Dishwasher cutoff mid cycle and would not power back on
Followed the YouTube video linked with the part ordered and it was an absolute dream
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Burt from JEFFERSON, MD
Parts Used:
W10712394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The plastic prongs holding one of the four wheels broke off allowing the upper rack to sag when pulled out.
I ordered part PS10064063, metal left and right rack adjusters that should be more durable than the plastic parts that broke. To install, I watched this YouTube video (https://www.youtube.com/watch?v=otUn8eoceBw), pausing and rewinding as needed. Piece of cake! FYI, when the axle broke, the small little plastic prongs stopped the grinder, which caused the dishwasher not to cycle. Fortunately, that was repaired under extended warranty, but the rack wheel was not covered. The repairman said the grinder (in most dishwashers these days) is a very delicate blade. They can't really grind much - even tiny plastic pieces.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JDB3600AWX4
121 - 135 of 899