JDB3650AWY2 Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jan from MAUMELLE, AR
- Parts Used:
- W10712394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
The part holding the wheels broke from age
One side at a time. Removal a bit difficult, but first side took longer. Second side was a cinch. It would be nice if they had better pictures, but it was a fairly straightforward repair. Nice to have it done and working again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from COOKEVILLE, TN
- Parts Used:
- W10648041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Pin hole leak in valve body.
Kill power to unit. Turn off water supply. Remove front access panel. Remove screw holding valve housing. Remove valve. Disconnect water lines. Replace valve in housing. Reconnect water lines with addition of thread tape. Reinstall valve and housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from DAYTONA BEACH, FL
- Parts Used:
- W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original plastic roller mounting posts on the upper tray had failed, rollers fell out and drawer could not close.
The kit number PS10064063 has much improved stainless steel framework. It's apparent the manufacturer recognized the deficiency of the original design. The instructions are adequate but the minimal essential to do the job. The images on the instruction sheet are low quality. Removal of the old parts isn't well instructed. Removal of the clips holding the failed roller mechanism was obvious, but the only way I could see to remove the adjuster was to pry it apart with a flat head screw driver. The Philips-to-hex head adaptor for installing the only two screws for each side that are needed in the new parts is a nice touch, so it isn't necessary to buy a hex screw driver. All in all a very satisfactory conclusion, since the extended warrantee service had declared the model to be unrepairable. The repair kit at reasonable price avoided the problems of having to remove and replace the dishwasher which otherwise is very satisfactory
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from PAWCATUCK, CT
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Absolutely no power to the unit.
I went on line and saw a video mentioning it may be the fuse and in order to verify that, take piece of scrap wire and jump pass the fuse.If the lights come on then its the fuse,I did and it was.So I found your web site, typed in the word fuse and the part number came up w/ your video showing how to install it. It was GREAT and what a great idea too having the video available w/ the part! I killed the power and I unscrewed the screws and placed them in the pattern they came out of because some are longer than others. I supported the front cover with my knee and had found the wires in advance so I knew which ones to cut, strip and screw into the new replacement part.I replaced it back in the snap on fuse holder and re-screwed it back together starting with the latch ones, using a criss cross pattern like on a tire. And that was that...I will DEFINITELY use this site again...........hopefully not for a while! Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from GALLATIN, TN
- Parts Used:
- W10712394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Orig. top rack guide failed. Was apparently a poor design that was redesigned
The most difficult part was taking the old, snap-together, parts off. The new parts were easy and quick to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BEND, OR
- Parts Used:
- W10712394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The photos weren't very clear.
The new part has been modified so I was not replacing with "like" parts and with the photos being not very clear, it took a bit longer to figure out what went where. Also it took a little time to figure out how the old adjuster came apart but it really didn't matter if I broke it, it was broken already.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earnest from Severna Park, MD
- Parts Used:
- W11196317
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking intermittantly
First I replaced the lower door seal then I replaced the door gasket. The instructions were clear so both were pretty easy. Unfortunately neither fixed the leak. After further research I discovered that the screws on the pump had become loose. I used a torx driver to tighten the screws. Time will tell, but I am pretty confident that this has fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Sallisaw, OK
- Parts Used:
- WP717273
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes would'nt come clean or dry from torn boot
Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from HOUSTON, TX
- Parts Used:
- WPW10491331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor to no cleaning lower basket
lower wash arm cracked by spinning into items hanging out of bottom of basket. part twists and snaps right in. glue did not fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from YORKVILLE, IL
- Parts Used:
- WPW10238411
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Retainer came off and was partially melted during a wash cycle
Called and with the help of Brandon in customer service the part was ordered,. It was a simple fix.. just snapped into place. Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from COLUMBIA, NJ
- Parts Used:
- W10258275
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to control
0) assure main power was off
1) Opened up the panel assembly according to the instructions and the partselect video using the torx driver.
2) snipped the wires from the old part
3) patched in the new part by twisting the wire ends, inserting them into the assembly and tightening the screws.
Had my dishwasher up and running again within 15 minutes.
1) Opened up the panel assembly according to the instructions and the partselect video using the torx driver.
2) snipped the wires from the old part
3) patched in the new part by twisting the wire ends, inserting them into the assembly and tightening the screws.
Had my dishwasher up and running again within 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ginger from DONIPHAN, NE
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
top of spray arm separated from bottom causing not to hold pressure and spin
Pulled up old spray arm and snapped new on in place. Took less than a minute and no tools. Dishwasher is like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!