JDB9800CWP1 Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Peter from BIRMINGHAM, MI
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Dishwasher door had lost springback
1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from WICHITA, KS
- Parts Used:
- W11259786
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Spot welds on track rusted and broke.
Pulled out dishwasher, removed 4 bolts holding the track to the dishwasher, replaced track and installed the 4 bolts. Pushed back the dishwasher and works like new. The new tracks are riveted instead of spot weld and will last longer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW BERLIN, WI
- Parts Used:
- WPW10531320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher wasn't draining
Took minutes to repair. Unhooked the electrical plug connector to the drain pump. 1/4 turn to the left and pump was off. Just the opposite to install new pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edna from WEST MONROE, LA
- Parts Used:
- WPW10653840
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When cycling through it would stop up to 3 times & have to be restarted.
Replaced door latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LOUIS from RAYNE, LA
- Parts Used:
- WPW10082853
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original Tine Pivot had broken
I looked at the position of the remaining Tine Pivot, since there are four on this dishwasher upper rack, and positioned the replacement pivot and pressed it into place. It was a snap (excuse the pun!). NOTE: My dishwasher's Model Number was not in the list provided herein. I had to search a couple of models to find the Upper Rack that looked like ours and to find the Tine Pivot replacement part that looked like ours.That process took longer than the "repair".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paula from ASHEVILLE, NC
- Parts Used:
- WPW10531320
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The drain Pump failed
Took the kick plate off without removing the the machine.
Reached in and turned the existing pump to loosen it. Then disconnected the wire.
Reversed the process to install the new pump.
Reached in and turned the existing pump to loosen it. Then disconnected the wire.
Reversed the process to install the new pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ELGIN, OK
- Parts Used:
- WPW10546503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Upper dishwasher rack broken
Removed the old rack clips from the top rack, freeing the rack and removed the bracket holding the adjustable bracket
Replaced the rack bracket and hung the rack back onto the rails
Replaced the rack bracket and hung the rack back onto the rails
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Scottsdale, AZ
- Parts Used:
- WPW10082853
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A bracket was missing on the top rack of dishwasher
Easy. Part just snapped in and took all of about a minute. Now the top rack doe snot slide back and forth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from ROLLA, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
installer from lowes di not do it right, forgot to put scew in, instead he used shims, as usuall no more installs from Lowes
followed directions, a kid could have done it,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Galveston, TX
- Parts Used:
- WPW10082853
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing tine pivot
Pushed to be into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from sullivan, OH
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door of the dishwaher banged open
Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from SICKLERVILLE, NJ
- Parts Used:
- 4317824
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ACWORTH, GA
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
replaced broken door balance link
Shut off power to dishwasher.Pulled dishwasher half way out from cabinet, careful not to disconnect waterline, drain-line, and electrical connections. Replaced roller assemblies and connected new door balance links to springs as shown in the great video featured on your website. Thank you for the great pricing, speedy service, and the install instructions. I am happy!
Was this instruction helpful to you?
Thank you for voting!