JDB8700AWS0 Jenn-Air Dishwasher - Instructions

Had to remove 2 screws fastening dishwasher to counter. Also removed bottom faceplate to expose the legs and to be able to lower them. Other sites recommended disconnecting the drain and water line but I did not have to do that, I had enough slack in the lines. I got the dishwasher about halfway out of the cabinet and then was able to remove the 4 screws holding the right track. Put the new track in and was good to go. Problem was that the left track broke and fell off a few days later. Still was an easy fix and thanks to PartSelect it was not very expensive.

Upper tray removed and each rack adjuster removed and replaced one after the other. Only tool was screwdriver. Only knowledge was from the online videos. Only took 30 minutes or so. The repair could have been done more quickly if I wasn't fearful that the smaller plastic parts would break when pulled or pried away from the rack adjuster. The only mistake was not making sure the adjuster tabs were fully engaged in back and clicked in the front attachment.

Turned off water supply to the unit. Removed plastic cover at bottom front. I only had to disconnect the copper water line to slide the unit about 1/3 of the way out. I then was able to reach the wires, disconnect them and use a stubby box/open end wrench (5/8? don't remember for sure) to remove the plastic nuts. I then opened the door, removed the bottom basket and slipped the element right out. Installation of new part was reverse.

Turn off power. Remove front panel -10 torx screws. Unplug two control panel wire connectors. Remove CP by prying bottom up with flathead screwdriver. Click in new CP and plug in 2 connectors. Replace front panel.
Turn on power and run test cycle

Take out the upper dishwasher rack. Place the adjuster towards the back of the upper each place attachment clips to secure adjuster and the adjuster clips to the back of the housing. Check to back sure adjuster move up and down and click back into place. Your installation is complete. Good luck!

Unscrewed mounting screws, pulled dishwasher out halfway, replaced arms, 4 screws each side .....very simple 30 min tops. Parts perfect and quick delivery!

I followed the video and even though my dishwasher was slightly different from the one shown, everything worked well. I was lucky that I had enough clearance to pull the dishwasher away from the countertop far enough to make the repair, without having to remove any dishwasher wiring below. I replaced both side tracks, even though only the left side was broken.

PartSelect intentionally shipped obsolete part that could not possibly fit a dishwasher. The part looked to be a rectangle door seal for a freezer/ref. You make it impossible to return the part. I find it interesting that you sent the correct install video and wrong part.
Suggestion: After you print a shipping label take a picture of the part and shipping label before it is boxed. The customer should not have to send you a picture of the wrong part and the serial number of the appliance for a refund. You did not need the serial number to ship it.

I will never use your company again William Dewberry

After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.

I am an 84 year-old woman so I asked another woman friend to help me. We removed both shelves from interior of dishwasher then unscrewed the first screw of the slim plastic piece on the top of the interior; then the second screw. We pulled the plastic piece gently down, removed the little round part out of the groove. We placed the new round part in the groove (ball down), pushed the spinner onto it so it would click on & hold. That required a bit of strength. Replaced screws & it was done!

Ordered the door gasket and replaced it. Worked perfect. The trick was to stretch the gasket a little as it went around the top curvatures. It would stick out some and not sit as flat as on the top and sides. This helped it to flatten down better.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Disconnected the water hose entering and one electrical plug alone with one screw that holds the valve to the machine. Replaced the old with the new and it worked.

Per suggestions from other reviews, I looked for You Tube videos for replacing this part. The video I used was completely necessary, but moved way too fast, so required lots of stopping, rewinding and starting again. But I managed to get the old rack adjuster removed and the new one installed without too much trouble.
Then I tried installing it in the pull-out rail. The front connector on the new adjuster would not fit into the appropriate slot. Initially I thought maybe the part was defective, but determined that the dimensions were as accurate as my eye and tape measure could evaluate. Finally, I settled on the expedient of filing away at least 1/16" from one edge of the slot so that the connector would drop into place.
Not sure why this discrepancy existed but the problem appears to be resolved.

The 1st person i had contact with wasn't any help choosing the correct part. Paid about $30.00 for the wrong part. Paid $8.00 more to ship the wrong part back for reimbursement. Meanwhile my son went to a local repair shop and got the right part for less than $40 and the repair shop installed the part on the rack for free
I was not happy with Part Select! Part Select cost me time and money and didnt get the job done