JDB1090AWB36 Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lynne from NEWNAN, GA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Basket had holes in it from repeated use of holding sharp utensils.
Just replaced with new basket. Fit like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denis from JACKSONVILLE, NC
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out basket
Took old one out And placed new one in dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- betty from GEORGETOWN, TX
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Basket broke----bought a new one!
opened door---- took out old basket--threw it away. set new basket in its place!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Groff from WVisconsi Rapids, WI
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom of the old basket was breaking and silverware was getting stuck
Open the door and remove old basket. Place the new basket in its plave. Time elapse approximately 20 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Anaheim, CA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Used Dishwasher In Our Condo Had No Silverware Basket.
Ordered silverware basket, placed into the proper position. Easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francine from Bristol, CT
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Top wash arm kept falling off.
I had to remove the the old retainer from the old wash arm ,install it on the new arm by snapping it on then I snapped the arm with the retainer up top of dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Ballwin, MO
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic in silverware basket cracked so utensils kept falling through/getting stuck
The basket did not include the handle (something I didn't notice when I ordered it). I simply removed the handle from the old basket and placed it on the new basket.
Having utensils falling through was really getting old. This was $25 well spent.
Having utensils falling through was really getting old. This was $25 well spent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Glenwood Springs, CO
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom of basket broken
take handle off old basket put on new basket done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Fort Myers, FL
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old basket seperated on the bottom.
Removed the handle from the old basket and put it onto the new basket. The new basket is great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Franklin, WI
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher arm keeps falling off.
I bought 2 Maytag appliances, a microwave and a dishwasher - they are both crappy!
The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.
The arm has a small bracket that can snap off and on the main water tube easily without tools.
Changing it was a snap!
The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.
The arm has a small bracket that can snap off and on the main water tube easily without tools.
Changing it was a snap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PORT JEFF STA, NY
- Parts Used:
- W11082871
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water inlet valve had to be replaced.
I pulled out the dishwasher enough to tip it back and put a block of wood underneath the front leveling foot.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from NICOLLET, MN
- Parts Used:
- WPW10192799, WP6-917647
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dishes not getting clean. Soap residue on dishes after wash.
After disassembling accumulator assembly looking for reasons that washer not washing properly, I noticed accumulator filter had failed. The plastic (or whatever material it is) covering the holes was torn in a couple of different holes. Realizing that this was not the reason for the loss of pressure I investigated a little more and found that water arm going into the docking station was extremely worn with much play. Water pressure was compromised because of it. I replaced filter and docking station and now its like a new dishwasher again. Saved a dishwasher from the landfill!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conrad from BAY ST LOUIS, MS
- Parts Used:
- WP6-916881
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace mounting brackets
Took a while to figure out what had to be done. Brackets have to go under the metal frame which involves dropping the compartment. That is done by removing the screws which are hidden under the door gasket. Once I knew what had to be done it was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from SAINT LOUIS, MO
- Parts Used:
- W11082871
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Dishwasher would not fill
Turned off water at the shutoff valve. I did not turn off the power, but it is recommended you do so. I pulled the dishwasher out from under the cabinet and used a car jack to lift the front off of the ground. Disconnected the water supply and the rubber hose that fills the dishwasher tub. There are two 7mm screws that hold the water pump to the frame. If you do not have a 7mm socket, the easiest thing to use is an interchangeable screwdriver. When the screw bit is pulled out, the empty screwdriver is a 7mm. Used adjustable wrench to remove the brass water port for the supply line. Teflon tape to all connections and hooked everything back up. My supply line was old and was leaking, so I had to run out and get a new one, so that added about 30 minutes to what would have been maybe a 20 minute repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert d from MOORHEAD, MN
- Parts Used:
- WPW10275768
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door didn't seal tight. So when it would go into rinse mode it would leak water on my floor
The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.
Was this instruction helpful to you?
Thank you for voting!