JDB1090AWW36 Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gerald from Newington, CT
- Parts Used:
- WPW10275768
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken handle assembly.
Removed inside cover.
removed part.
disconnected switches.
plugged wires onto new part.
placed part in.
put inside cover on and screwed down.
Note: be careful of the bottom of the inside cover.
removed part.
disconnected switches.
plugged wires onto new part.
placed part in.
put inside cover on and screwed down.
Note: be careful of the bottom of the inside cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Greenville, PA
- Parts Used:
- WPW10275768
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Broken door Latch
Removed all the screws holding the inside panel of the door to the door itself. Lifted out the old broken door latch. Pulled the wire clips from the 2 switches located on either side if the door Latch assembly. This is a bit difficult. You have to keep working the wire clips back & forth; Up & down until the clips are free from the switch metal contacts. Reinstall the wire clips on the new door Latch assembly making sure you attach the black wires and white wires on the same side of the new latch assembly as on the one removed. Replace the new latch assembly aligning the mounting holes on the door with the new latch holes. Replace the inside panel aligning the holes and replace the screws. The screws were the star head type so you need a special driver bit. I used the box the latch came in the prop up the inside door panel while I worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from NICOLLET, MN
- Parts Used:
- WPW10192799, WP6-917647
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dishes not getting clean. Soap residue on dishes after wash.
After disassembling accumulator assembly looking for reasons that washer not washing properly, I noticed accumulator filter had failed. The plastic (or whatever material it is) covering the holes was torn in a couple of different holes. Realizing that this was not the reason for the loss of pressure I investigated a little more and found that water arm going into the docking station was extremely worn with much play. Water pressure was compromised because of it. I replaced filter and docking station and now its like a new dishwasher again. Saved a dishwasher from the landfill!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conrad from BAY ST LOUIS, MS
- Parts Used:
- WP6-916881
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace mounting brackets
Took a while to figure out what had to be done. Brackets have to go under the metal frame which involves dropping the compartment. That is done by removing the screws which are hidden under the door gasket. Once I knew what had to be done it was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PORT JEFF STA, NY
- Parts Used:
- W11082871
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water inlet valve had to be replaced.
I pulled out the dishwasher enough to tip it back and put a block of wood underneath the front leveling foot.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MARBLEHEAD, MA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Some of bottom wire in the silverware basket had rusted out allowing silverware to fall through and interfere with rotating arm.
The "repair" was actually a replacement. My wife did it. She took out the old, damaged basket and dropped in the new, replacement basket. She removed the slotted lids because she doesn't think they are necessary and she doesn't like them. I got the old basket for holding small items in my workshop. The lids will be thrown away, unless I can come up with a use for them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from RIVERSIDE, CA
- Parts Used:
- WPW10275768, WP99003149
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door wouldn't shut
Remove the screws , opened door panel. Removed switch with latch and replaced with new parts. Replaced panel and screws. Install completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Groff from WVisconsi Rapids, WI
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom of the old basket was breaking and silverware was getting stuck
Open the door and remove old basket. Place the new basket in its plave. Time elapse approximately 20 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from TWINSBURG, OH
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The silverware basket needed replacement since there were cuts in some places on the bottom which caused utensils to fall partway through.
Very simple. Just replaced the old one with the new one. Voila!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from NEWNAN, GA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Basket had holes in it from repeated use of holding sharp utensils.
Just replaced with new basket. Fit like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- betty from GEORGETOWN, TX
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Basket broke----bought a new one!
opened door---- took out old basket--threw it away. set new basket in its place!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Chester, NH
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut
Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Franklin, WI
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher arm keeps falling off.
I bought 2 Maytag appliances, a microwave and a dishwasher - they are both crappy!
The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.
The arm has a small bracket that can snap off and on the main water tube easily without tools.
Changing it was a snap!
The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.
The arm has a small bracket that can snap off and on the main water tube easily without tools.
Changing it was a snap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from STURGIS, KY
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced silverware basket. No problems!
Lifted out old silverware basket. Set new basket in. Took approximately 20 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SHAWNEE, KS
- Parts Used:
- WP99003148
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The wheel would fall out of the track constantly
I had to lightly pry off the long piece of plastic next to the wheel assembly because I had to twist the assembly counter clockwise to remove the old one. Also had to place the new one so that it rotated clockwise to seat it. Then replaced the other plastic piece.
Was this instruction helpful to you?
Thank you for voting!