JDB1080AWW36 Jenn-Air Dishwasher - Instructions

Removed ~12 screws holding the inside liner onto the door. Pulled off the two connectors (one with black and one with white wires). Replace the handle and latch mechanism. Redid connections and replaced screws. Viola. (Be sure to buy BOTH the handle and latch mechanism- I don't see how you could easily install the handle on the mechanism myself, and what broken in my case was the black handle).

I removed the screws around the top and halfway down the sides of the inside of the door. I found that you dont have to remove all 10 screws to access the assembly. Reach in and pulled out the assembly, there was enough slack to pull it out above the door. Pull the connectors off and slide the new ones on. Set the new assembly back in place, insert the 2 top screws first, and then the rest. That was it...very simple to change.

Replacement basket did not include handle so needed to pry old handle off broken unit to use on the new one. Used screw driver to pop loose clips which attached to basket. Had to stick tooth picks broken in half under them to hold out until all four clips were opened at once - then handle could be pulled off. Easily snapped it back on to the new basket and repair was done. Can't get any easier than this!

Dishwasher is in our summer cabin in Colorado so everything has to be drained for the winter. Not really sure whether this leak was freeze caused or that the valve was just old. Couldn't find a crack when I got the old one apart; might have been just an O ring needed. Anyway, just follow the video provided by this site for replacement of the valve; really easy. Biggest hassle for us was getting the dishwasher out (and back in) as it was wrapped in insulation which made the fit really tight. Thought I had everything I needed when I started but didn't have teflon tape which is needed for the brass fitting connecting the water supply to the valve (fitting is in your old valve and will be reused with the new one).

1. Shut off water supply

- Remove water line and drain hose if you need to. I was able to simply move the dishwasher forward some to do this repair without disconnecting

2. Remove access panels on the bottom.
3. Open the door
4. Remove Door Gasket carefully (do not stretch)
5. Use torque 20 driver to remove 6 screws that were under the gasket

- Some of the screws were rusted for me so I had to use kroil, a pick to clean out rust, and a hammer to help get the torque driver in enough to remove the screws. A local hardware store had replacements.

6. Use Phillips screwdriver to remove screws holding mounting brackets
7. Carefully move dishwasher out some (Careful if you have a copper water hose you may want to disconnect it)
8. Remove the strike if it is attached above the metal bar
9. Lift the metal bar and push down on the tub to make room to remove the old mounting brackets (slide them up, forward, and to the side)
10. Put new mounting brackets in place (put mounting bracket under bar, slide over into place)
11. Reverse the order at this point.

Be careful not to stretch the gasket. I soaked mine in vinegar for a bit and gently washed with dish soap to remove deposits.

n/a

I removed the screws from inner door panel.The 2 top screws also hold the latch assembly in place.I then lifted the panel, removed latch assembly, unplugged the 2 wires ,then installed new part in reverse order. Reinstalled screws in inner panel. Oh yes,first turn off power first at breaker box.

This couldn't have been easier. After unsnapping the docking station from the dishwasher, I aligned the two flapper valves that come with the unit and pressed them into place. I then pushed the new unit into place by pushing first on the left side and then the right until it clicked into place.
I looked at the old one and found that one flapper was gone and the gaskets were deteriorated. What made the whole process easier was buying from PartSelect. I have bought from them before and will again.

1. Turned off power. 2. Unscrewed ten screws holding inside of door in place. 3. Lifted cover enough to access latch - helpful to have someone to hold this while doing the job. 4. Disconnected old latch assembly on each side - this was the hardest part as they were stiff and needed to be pulled hard. 5. Attached new latch assembly. 6. Screwed door panel back on. 7. Switched power back on. So easy and saved about $150. This stuff is NOT HARD and I just wish more people had the gumption to do repairs themselves instead of paying 'experts' to do exactly the same job.

Just inserted new basket - used butter knife to remove handle from old basket so it could be inserted on new basket. It was helpful to see comments left by others that they had same problem with their baskets and how one used a knife to remove old handle. That was a helpful hint.

It was easy. We removed the handle from the old basket and put in on the new and set it in place. Wonderfully easy.

I put the silverware basket in the dishwasher. Unfortunately, I also purchased a cover and handle thinking they were needed. Now I need to see about returning the extra parts or just eat the cost.

No repair - just replaced basket. Although picture on site made the basket look light gray, which is color of our dishwasher interior but the new basket ordered is very dark gray.

Hi, Not really a "repair," but a replacement. The part came quickly, was what I needed. Done.

just replaced the basket. Simple enough but the best thing was the speed I received the part.