JDB1095AWS44 Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janet from STURGIS, KY
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced silverware basket. No problems!
Lifted out old silverware basket. Set new basket in. Took approximately 20 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from OREGON, OH
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My old silverware basket was wearing through on the bottom and silverware was sticking through
Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring spoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from CREEDE, CO
- Parts Used:
- W11082871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
Water leaking under dishwasher
Dishwasher is in our summer cabin in Colorado so everything has to be drained for the winter. Not really sure whether this leak was freeze caused or that the valve was just old. Couldn't find a crack when I got the old one apart; might have been just an O ring needed. Anyway, just follow the video provided by this site for replacement of the valve; really easy. Biggest hassle for us was getting the dishwasher out (and back in) as it was wrapped in insulation which made the fit really tight. Thought I had everything I needed when I started but didn't have teflon tape which is needed for the brass fitting connecting the water supply to the valve (fitting is in your old valve and will be reused with the new one).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from RIVERSIDE, CA
- Parts Used:
- WPW10275768, WP99003149
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door wouldn't shut
Remove the screws , opened door panel. Removed switch with latch and replaced with new parts. Replaced panel and screws. Install completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Groff from WVisconsi Rapids, WI
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom of the old basket was breaking and silverware was getting stuck
Open the door and remove old basket. Place the new basket in its plave. Time elapse approximately 20 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert d from MOORHEAD, MN
- Parts Used:
- WPW10275768
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door didn't seal tight. So when it would go into rinse mode it would leak water on my floor
The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from TWINSBURG, OH
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The silverware basket needed replacement since there were cuts in some places on the bottom which caused utensils to fall partway through.
Very simple. Just replaced the old one with the new one. Voila!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from NEWNAN, GA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Basket had holes in it from repeated use of holding sharp utensils.
Just replaced with new basket. Fit like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denis from JACKSONVILLE, NC
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out basket
Took old one out And placed new one in dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- betty from GEORGETOWN, TX
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Basket broke----bought a new one!
opened door---- took out old basket--threw it away. set new basket in its place!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MARBLEHEAD, MA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Some of bottom wire in the silverware basket had rusted out allowing silverware to fall through and interfere with rotating arm.
The "repair" was actually a replacement. My wife did it. She took out the old, damaged basket and dropped in the new, replacement basket. She removed the slotted lids because she doesn't think they are necessary and she doesn't like them. I got the old basket for holding small items in my workshop. The lids will be thrown away, unless I can come up with a use for them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Shoreline, WA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our utensil basket had holes in the bottom and silverware fell through.
Ordered a new basket. Tossed out the old one. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from NICOLLET, MN
- Parts Used:
- WPW10192799, WP6-917647
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dishes not getting clean. Soap residue on dishes after wash.
After disassembling accumulator assembly looking for reasons that washer not washing properly, I noticed accumulator filter had failed. The plastic (or whatever material it is) covering the holes was torn in a couple of different holes. Realizing that this was not the reason for the loss of pressure I investigated a little more and found that water arm going into the docking station was extremely worn with much play. Water pressure was compromised because of it. I replaced filter and docking station and now its like a new dishwasher again. Saved a dishwasher from the landfill!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from BELLEVILLE, WI
- Parts Used:
- WP99002659
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Noisy
This site has a great video on how to do this. Just follow that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PORT JEFF STA, NY
- Parts Used:
- W11082871
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water inlet valve had to be replaced.
I pulled out the dishwasher enough to tip it back and put a block of wood underneath the front leveling foot.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.
Was this instruction helpful to you?
Thank you for voting!