JDB1250AWS Jenn-Air Dishwasher - Instructions

After receiving the latch assembly, which arrived rather quickly, I found the handle itself was not enclosed in the package. Therefore this repair was delayed and after several calls to the 1-800 number I was informed the company had discontinued the distrubution of the handle. They offered a full refund, however I'm still waiting for the return labels so as to ship the latch back.

Now on the brighter side, the company representative put me in touch with a local distributor that did carry the latch/handle assembly as one piece and for a lot less money.

For those who are attempting the repair, don't worry, It was very simple. Just remove hex screws, lift the inside panel, unplug the two connectors and insert the new assemply.

Must say my wife was very happy to have the dishwasher up and running again.

Good luck !

Remove the water distributor, filtration plastic parts down to the base of the tub and clean of debris. Sometimes a small piece of plastic from the upper glass tray can break off and find its way into the bottom. Once its cleaned this section and be put back. Had to remove the unit from the cabinet and replace the drain motor and also cleaned the drain hose that runs to the garbage disposal. Most times this problem is caused by a blocked drain line or debris in the bottom of the tub constricting waster water from getting into the drain motor.

When the (overpriced) replacement silverware basket arrived (rapidly, within a few days of my ordering) I was shocked and angry that the handle for the basket was not included--nor were instructions included as to how to remove the old handle from the old basket in order to fasten it to the new basket. Therefore, I spent a considerable amount of time trying to pry the handle off the old one, which was quite tricky: There were four slots which held the plastic "catches", and they had to be pushed out simultaneously. I had to fiddle with it for at least a half hour, trying various implements, until I found that I could push them out simultaneously by wedging butter knives into the slots and then easing the handle off. (I was careful to position myself so that I wouldn't slip and stab myself with the blunt butter knife.) After that, the handle snapped fairly easily into the new basket's slots.
In the end, while I was glad to be able to recycle the old handle, I wish that the basket and shelves were made more durably so they wouldn't have to be replaced, or that they could be replaced at a more reasonable price.

Snapped new wheel on

Open the door and remove old basket. Place the new basket in its plave. Time elapse approximately 20 seconds

take handle off old basket put on new basket done

Removed the handle from the old basket and put it onto the new basket. The new basket is great!

opened door---- took out old basket--threw it away. set new basket in its place!!!!

Very simple. Just replaced the old one with the new one. Voila!!!

Just replaced with new basket. Fit like a charm!

The "repair" was actually a replacement. My wife did it. She took out the old, damaged basket and dropped in the new, replacement basket. She removed the slotted lids because she doesn't think they are necessary and she doesn't like them. I got the old basket for holding small items in my workshop. The lids will be thrown away, unless I can come up with a use for them.

Remove the screws , opened door panel. Removed switch with latch and replaced with new parts. Replaced panel and screws. Install completed.

Pulled the removable end caps off of the sliding track that the wheels roll on and then pulled the top tray out of the dishwasher (works like a sliding drawer in your kitchen). Removed a half dozen hex screws and threw out the old wheel housing. Set the new wheel housing and new wheels in its place and re-inserted the hex screws. Slid the top tray back into the sliding track and re-inserted the end caps. Done.

Lifted out old silverware basket. Set new basket in. Took approximately 20 seconds.

The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.