JDB8910AWQ Jenn-Air Dishwasher - Instructions

We ordered the replacement part for our Maytag model and when it came we saw that it was different than the original part. The original part had 8 wheels with a higher left hand side. The replacement part had only 6 wheels and no higher side. The replacement part would not pull in and out evenly and was a bit too narrower. We called Parts Select and told them our problem and they are going to refund us in full and take back the part they sent. Alas we will have to buy a new dishwasher. We would use Part Select in the future for replacement parts.
Alice
Cambridge, MA

I aligned the V-shaped tabs on the inner side of the part with the slots in the mating part and simply pulled the old part out (it was already disengaged from the wheels in the metal rail). I then inserted the new part into the slots. One side went in well, but the other side required the part to be bowed slightly to match up the V-shaped tab with the slot. Then the hard part was getting the wheels in position to snap them on. Once in position, it took a bit of effort to engage the snaps in each wheel. I was afraid of breaking the new part. These snaps are very stiff and even with the notch between them there isn't any give, but I was able to apply enough constant, steady pressure to finally get them to snap in without breaking.

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

Remove bottom rack. Unscrew the retaining ring on the wash arm, remove along with wash nozzle. Unscrew the eight retaining screws on the filter cover and remove (be carefull not to lose the two plastic bushings). Pick off and set aside the wash fan. Remove the six retaining bolts on the discharge housing. Pull up and remove the discharge housing. Remove the gasket (buy a new one, cheap and easier) with small screwdriver. Push gasket into new assembly. Under plastic nut with pliers and take off the plastic bushing that the wash arm rides on. Install new housing assembly with the parts that was taken off in the reverse order. Be carfull when installing the filter cover to make sure the drain outlet is aligned or mated to drain. Gently push down until the filter in down and continue reassembly.


(PS: Never use Sears parts, they extrembly slow as well unable to deliver on time).
Wash your dishes

I took apart the lower spray arm apart and removed the 6 hex screws. I noticed that the little plastic circle thing had been ripped off the dome-shaped thing. I replaced the part and put it all back together.

Was extremely easy to remove that existing rackings(upper and lower), install the new racks and snap in the new spray tower. It now looks like we have a new dishwasher. We are hoping that it will last another 10+ years.
We will recommend your site to friends.

Replacing my dishwasher racks was very easy. I followed the guidance on the PartsSelect.com website for replacing the upper rack. Replacing the lower rack was only challenging when I couldn't figure out how to remove the water sprayer from the old rack and place it in the new rack. A quick search on Google.com and I learned to turn the sprayer counter-clockwise to remove it and then clockwise to put it in the new rack. Worked like a charm! I would recommend PartsSelect.com to anyone. Easy to use, parts came quickly, and I appreciated the guidance from others.

Repair was simple. Diagnosis was wrong. Switch did not fix problem. Most likely a control electronic assembly.

removed old one left wires attached until i took them off and replaced with new board one at a time. repair was easy. repair company wanted 300.00 to do what i did for the cost of part 149.00. it took more time to remove the screws in the door then it did to install the control board.

Piece of cake. I panicked for a minute before I realized that there was a threaded brass 90 in the inlet valve. It looked like it was the wrong part for a minute. Once I got the 90 reinstalled in the new valve, I had it back together in 10 minutes. It seems to be working better.

First I removed the screws that held the door together. I then unplugged all the wires from the back and removed the screws holding the LED panel in and unsnapped it from the clips. Just reverse the process putting the new one in. Worked great.

We twisted the tower counter clockwise to remove from the old rack. It was a bit tight but came off quickly. Then inserting the tower into the new rack went very smoothly. That's all there was to it. The new rack did not have a place where I could attach the flip down shelf, but I rarely used it anyway. Love partselect. They helped me avoid buying a new dishwasher. Using Cascade pods, my dishwasher cleans like it is new and it is 25 years old!

Dish rack not same as original. No raised section on right for drop down ledge. Also the old rack had a section for wide rim bowls. New one is for plates only. Otherwise it is OK

I took off the front bottom panel for an easy access. The valve is located on the left. Shut off water to the dishwasher. Remove the bracket that holds the valve. Remove hoses and 2 wires on the valve switch. Install new valve by revesing the steps above.