JDB9910AWQ Jenn-Air Dishwasher - Instructions

The lower spray arm of this model has a chronic problem with the plastic seams splitting and the horizontal blast causing door leaks. This was the third spray arm replaced on this unit. Rather than simply replacing the spray arm with the OEM device purchased, I used a solder gun to reweld the seam on the spray arm. I expect that the additional welding will provide many more years of service than the OEM replacement part. They should really improve the quality of the replacement part to prevent splitting. A metal replacement would be worth $50 and provide a better repair than the plastic arm.

Attaching the part to the door only took a few minutes but getting the dishwasher out over the hardwood floor that was installed after the appliance was put in was a pain. I had to remove a piece of the hardwood floor and use some technique to get it out of the opening so that the springs were visable. There is no problem after that. I would recommend using work gloves to stretch the spring over the retaining notch on the door so that you don't pinch your hand.

Simply had to replace the clips in the correct position. Would have been a five minute job if I had noticed which way around the old parts went before removing them from the dishwasher to find replacements. It's amazing hoe many permutations there were before it all fit together perfectly.

Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

We had tried to use dish washer cleaners, and they would work for a time, but we started spending more money on cleaner than we wanted. I ordered and then I replaced the lower spray arm. It took a little effort to get the top screw off, due to hard water deposits. The new one went on very easily, just screwed right in like the old one. It's working great and I really don't mind not getting a new one or paying for a service call!!!

Both racks are just roll out & roll new racks back in, no tools. Racks came in just 2 days, one was damaged in transit. Called to advise PartSelect of the problem. replacement rack was here within 2 days.
Great service. Jack

Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.

The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.

Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.

received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.

I recieved a different part than was in the picture and description that I ordered, and was billed twice for it. I wasn't able to fix my dishwasher

I removed the bottom rack by simply rolling it out of the dishwasher, and removed (unsnapped) the rotating spray assembly. It was easily snapped into the center of the new dishrack. Next, I removed the roller stops from the rail holding the upper dishrack by following the marks (arrows) on the stops. I rolled out the upper dishrack, and rolled in the new one. Finally, I snapped the roller stops back into position.

Ordered BOTH the front and rear tines as the front tine showed some superficial rust through the plastic covering in a couple of spots. Re-used the tine holders which were still solid condition and flexible. Snapped bowl holder tine unit out of dishwasher, snapped new tines in place, snapped unit back in dishwasher. Took 5 minutes or less. All other parts of the dishwasher rack were still in excellent condition with no cracked spots on the vinyl covering or rusted spots visible anwhere.

unscrew screen and cover and unbolt impeller replace with new parts. everything goes back together easily, anyone with even minimal repair skills should be able to do this repair.

Shut off the water and electric then removed the cover at the bottom then removed the water inlet valve and replaced it with the new one. Turned on water and electric. Replaced cover at bottom. Very easy and the part was shipped quickly. No problems and the dishwaser works great now!!

The replacement of the rack was straightforward, but the tower assembly had to be moved to the new rack. The fit is precise and fits only one way. I did break off one tab, but it is held just fine. .