JDB3610BWX Jenn-Air Dishwasher - Instructions

First I disconnected the dishwasher electric, water supply and discharge hoses. I then pulled the dishwasher out. After opening the door, I removed the retainer clip holding the upper wash arm, then the nut holding the top shower hose in place. Close the door and lean the dishwasher on its side to get at the underside where the other end of the hose is. Loosen the hose clamp and remove the top shower hose. Reassemble everything in reverse order. In hindsight, I didn't need to buy the new hose clamp or the tub top washer (I reused the originals). Good luck!

I removed the seven screws from the back panel of the door (special tool) and seperated the back panel from the front. My wife held the back up and I removed the two wax motors (detergent cup and rinse aid), which were clipped in place. I had turned off power to the dishwasher, so I simply unplugged each wax motor from the wiring harness, plugged the wax motors in and clipped them in place, making sure that the wiring harness was put back in the same place. Then I put the back panel back on the door, turned the power on and tested the repair. The dishwasher worked perfectly. Thanks to PartSelect for helping me solve the problem. The parts arrived in two days!

I took out both wax motors - tried switching the motors on the rinse dispenser and soap dispenser but they were both dead - new motors from partselect arrived fast - simple installation if you have the torx screwdriver for the door inner panel.

First I did the top - getting the ends off the track is simple, flip the ends "open" like a book on each side, and remove the caps. Pull out the rack, replace with the new one and replace the caps. Bottom rack was easier once I figured out how to remove the spray tower. Grab it firmly and twist. Place it in the new rack, and roll it into the DW. I'm a fairly handy woman, and this was quite easy.

With a straight edge screwdriver I carefully removed the plastic end caps on the rack support glider-shelves, replaced the old rack with the new rack, and then reattached the end caps.

I felt better about ordering the part Online after having talked to a sales person since there were several racks from which to choose. She reassured me that I was ordering the correct part number. I am a woman and 62 years of age, and I was pretty sure this installation would be a no-brainer. I just wanted to make sure I had the right part for the job.

Old rack assembly was rolled out , the plastic water disperser was twisted off of the old rack and placed on the new rack assembly. The new rack was rolled into place. Project complete.

Remove three phillip's head screws from the right- and left-side trim strips. Bow panel slightly to remove. Reverse steps to reinstall. Very easy repair.

First replaced rubber seal around door, which did not stop the leaking.
Then ordered insulation foam strip and replaced old one, which fixed problem. Put new strip over the old one because tub was slightly warped.
Very pleased with order speed and cost.

After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

removed clamps with screwdriver from bottom of dishwasher and clamp from sink drain. I taped the new hose to the old one and pulled it through. worked perfect.

First I unplugged the dishwasher since I was working on the electrical. I just unscrewed all the screws on the inside of the door till I could get down to the door latch. I found that a tiny piece of plastic had broken off of the white bracket that holds the electrical switches (these turn it on when the door latches and off when the door opens). I had to break several tiny plastic prongs off the old bracket in order to pull the switches out of it (gently so the wires wouldn't pull out of the switches) and the door handle latch fell out easily. Then it was easy to snap the switches back into the new bracket, and slip the handle latch back in, and screw everything back down. It worked! I've never worked on a dishwasher before but looking at the photos of all the various parts (even the ones I didn't need to use) really helped me to see how the things go together and to narrow it down to which part I would need. The dishwasher was totally un-usable and all I spent to make it run again was less than $5. Thanks to Partselect!

I did not move the dishwasher out. It is a fairly tight space underneath, but the water inlet valve is located toward the front, so it wasn't too bad. The steps were:

1) unplug the power and turn off the water to the dishwasher.
2) remove the 2 wire connectors.
3) use the nutdriver to remove the 2 screws that hold the valve to the side of the dishwasher.
4) use a wrench (5/8") to remove the nut where the water goes into the valve. This takes some patience since you can't turn the wrench very far in the tight space.
5) remove the water outlet hose by using pliers to squeeze together the clamp and move it up the hose. Then twist the valve to free the hose and remove it from the valve. The nibs on the clamp are small and take a little time to get them squeezed together. If the hose has been on there a long time, you will have to twist the valve a few times to free it up.
6) now you will have to remove the sleeve that the nut was screwed onto. I had to take the valve to my vise to hold it. Then it wasn't too hard to remove.
7) use teflon tape before you reassemble. Just go in the reverse order.
8) hope there isn't a leak. Mine didn't.

The new water inlet valve seems to have fixed the problem!

1- turn power off. 2- remove 7 screws to take door apart 3- remove 2 screws to take dispenser out. 4- i unhooked electic plug from it. 5- replace grommet and all back together. not bad to be 72 years old.

After examining the door and main seal around the dishwasher I thought everything looked okay. I looked online to order a new seal anyway and discovered from others that the leak was probably the insulation strip inside the door rather than the seal around the dishwasher. I ordered an insulation strip and it arrived a couple days later. I removed the seven screws of the interior door cover and disconnected the electrical. After removing the old insulation strip and installig the new one I reconnected the electrical wiring/plugs, put the door cover back on, and reinstalled the screws. Total time was about 15-20 minutes and the leak stopped. It was very easy and saved the cost of a repairman or a new dishwasher. I'm very glad that I "listened" to others and went with the new insulation strip.

Most difficult was figuring out how to release the top rack...just flip the end pieces to the side and out they come. Next was removing and reinserting the spray head in the bottom rack...just twist and take out then align and twist into place in the new rack.