JDB1080AWB Jenn-Air Dishwasher - Instructions

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

1) Turned off the power

2) I removed the screws on the plastic door.

3) The latch/handle assembly was right there.

4) I noticed that white and black wires fed each side. I noted which side did the black feed and the white feed.

5) I took a pair of pliers and held the white wire brackets and pulled the metal parts off. This is where the time took.

It took about 2 minutes per side.

6) I then slid the new metal parts in the white brackets.

7) I screwed it back.

8) Turned it back on!

9) Works great

Pretty easy job. You need torx tips for your screwdriver. An electric screwdriver got all 8 or 9 screws out of the door panel in about 60 seconds, separated inner door from outer door, pulled out handle assembly & disconnected wires, attached wires to new assembly, screwed it all back together. Be prepared... the handle will break again. It's just a bad design by Maytag. This Maytag model is so bad the company discontinued it. Beware of the control panel getting corroded from steam & failing. If replacing this panel, make sure you seal where the cable goes into the touchpad with some kind of waterproof glue, nail polish remover, or sealing tape so it doesn't happen again.

First I removed the torx screws halding the inner door panel on. I then seperated the door panel from the door and removed the latch assembly and disconnected the switches from the latch. After installing the switches on the new latch I replaced it between door and inner panel. Finally I replaced the torx screws and was finished.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

It is such an easy snap-on repair that a child could do it. I am grateful that your company had a picture so I could compare my broken part with the ones you guys have as I couldn't find my model number. I took my time to do the job right, so it took me almost 15 seconds! lol

Turn off the DW power (pull the fuse or turn off the circuit breaker) Open the dishwasher door. Remove the torx screws around the periphery of the door inner panel. Lift up the inner panel far enough to get at the door latch. Lift out the entire door latch assembly. There are two wiring connectors attached to microswitches on the latch assemby. Remove the connectors. The connectors were pretty tight, so I needed pliers to pull the connectors off the switches. Discard the old latch. Get the new latch, and plug in the connectors (keep track of which wires go on which side). Lay the latch down in the door so it lines up with the mounting holes. Lay the cover back down, start each of the torx screws into their threaded holes, then tighten them all. Don't over tighten. Turn power back on. Job done. It almost takes as long to type it up as it does to make the repair.

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

Repair was fairly easy. There are 11 screws You have to remove then simply unplug the electrical connection from the door latch/switch and plug in the new one line up the screw holes tighten them down and your in business.

1 - Unscrew the back of the dishwasher with a hex-type driver. The latch assembly will be resting inside the outer door assembly. Make sure power is turned off to the washer - there are a couple of "hot" wires that will attach to the latch assembly.

2 - Unplug the wires from the old latch and plug into new latch assembly.

3 - Place the latch assembly back in place and re-attach the two door pieces together.

4 - Turn power back on at the breaker.

5 - Load dishwasher with the stuff that's been sitting in your sink.

6 - Gloat to spouse/significant other that you just saved $100 by fixing it yourself.

Just a quick note of thanks for shipping the replacement handle for my Maytag dishwasher.  Service was superquick and I was able to save big bucks (no service call).  I called on Saturday evening and the part was here on Tuesday.  The young lady who helped me was awesome and a Pens fan to boot.  I seldom send these types of emails but my experience was worth sharing.

I had two problems with the dishwasher. The latch handle was broken and a line crack developed on the control panel just above the handle area.

1. Ordered the Latch Handle (LATCH ASSY (BLACK) MA) (Series 10); Part # PS1559543 from PartSelect. (Maytag’s part number is 99003347). PS1559543 received from PartSelect includes the latch, latch handle, and two switches.
2. Disconnected power to dishwasher. (I put the washer on timer mode; the control panel lighted up; turned off power supply at the circuit breakers box; control panel light was off; confirming that power was cut).
3. Opened the door, removed the torx T-20 screws from the inner panel (I used a cordless drill and one of the star shaped screw tip from a cheap Craftmans screw tips set)
4. The inner panel slid down down enough to expose the latch assembly. Since the latch assembly was held in place by the two of the screws removed, it was now only attached to two sets of wires through the switches on both sides of the latch assembly.
5. The next thing to do was to connecting the wires to the new latch assembly. I chose to use the switches on the old latch assembly. There were plastic hooks holding them in place. The switches readily slid out by slightly push back the hooks. There is a little knob on the switch, and had to be pushed back to slide into the new latch assemble.
6. To fix the line crack, I used a toothpick to apply plastic glue on both sides of the crack. Then lined up the latch assembly with the control panel and the dishwasher’s inner internal panel, put back the two top middle two torx T-20 screw to hold them in place. Excess glue was wiped off with paper towel wet with isopropyl alcohol. This saved me the expense of ~$60 for a new control panel. Don’t use crazy glue, it will discolor the plastic.
7. Put back the screws at four corners, then the rest. I set the clutch of the cordless drill at 2 so that the screws were not over tightened.
8. Let the glue dried overnight. The crack was fixed, the latch assembly works like when the dishwasher was new.

After checking repair places who wanted $140-$200 to repair the handle (most of it labor and transportation of course) I checked this website and read the do it your self testimonials the first one being wendy from florida and figured if she could do it so could I. . . Wasn't quite as confident as her so found a handy person (charged me $30). It was a "piece of cake" -- remove the 11 screws (allen screwdriver), unclip the wires to the handle (pliers), clip in the new one, replace the screws. I could have done it myself. Took 15 minutes.

Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.

Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around little knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.

1. Turned of Power via circuit breaker
2. Opened Dishwasher
3. Removed back of door (11) hex screws with electric driver
4. Removed latch assembly
5. Pried contacts from switches
6. One switch was more difficult to pry loose than the other
7. You will probably need a plier
8. Switch or connector may break but latch assembly comes with switches, so you just need to be careful not to break the connectors
8 Plugged connectors into new switches on latch assembly
9. Replaced latch assembly
10. Replaced door with (11) hex screws - two top screws hold assembly in place
11. Turned on circuit breaker and tested machine
12. Finished

Comments: This latch assembly was better constructed than the original and I expect it to last the life of the machine. If one of the switches wasn't so difficult to pry loose, then the repair would have taken ten minutes less to repair. Well worth the effort. Repair time was probably 20-30 minutes.