DW980B Jenn-Air Dishwasher - Instructions

First I had to unhook the electric, water line and drain hose. Then slide out the dishwasher. Took several days to find the drain hose - local stores only carried a 6 ft hose and I needed a 7 ft. Once I found it online, purchased it and recieved it I put it all back together and all is good.

removed inner door panel. tested ythe Wax motor that operates the soap dispenser latch. It tested OK so I removed dispenser assembly. replaced the worn plastic parts and reinstalled the inner door panel.

After removing the parts so I could get at the o-ring, I replaced the o-ring and restarted the dishwasher. Water was still getting past. Maybe has something to do with the difficulty of tightening around the short shoulder near the o-ring. To overcome the problem I applied a thin layer of Marine Goop under and over the o-ruing and reassembled the parts. Now no leaks.

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Took off the float, the jam nut was hard to get off, we ended up breaking the bottom piece of the float to get it off, but that was okay because we had a new float. The new float went on real easy and the jam nut went back on real easy. The foam insulation strip was real easy to get off we got a good hold of one end and striped it off slowly so there was nothing left on the door, then we cleaned the surface and put on the new insulation strip. We ran dishwasher to test it and there was no leak. Awesome. Cheap and easy to repair. We were impressed.

Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

I replaced the door latch grommet just as everyone else has described on this site. It was pretty easy. I was amazed that such a little piece of rubber can let so much water get by. The inlet valve was not too bad either. Take the two bolts out that hold the bracket to the dishwasher. Remove the rubber hose on the back side and take loose the two electrical connections. My water line was long enough to pull it out in front of the dishwasher. Then I took the water line loose and removed the fitting. Installed the new one in reverse order of what I just described. These items took care of the bulk of the leaking problem. But I am in the process of ordering a new door seal which I hope resolves the rest of the issue. Also make sure you check the upper and lower control arms to make sure the spray holes are free of debris. This dishwasher was full of pieces of clear plastic that caused the spray arms to spray indirectly and towards the cracks of the doors.

Once I pulled the old broken drain valve lever lifter off the shaft, the shaft rotated counter clockwise. I then had to turn shaft back clockwise so there was enough room to slip the new part on. Needle nose pliers worked great to hold it in place while regular pliers in the other hand was used to turn the shaft.

It was difficult to use the guide provided online to determine what position to place the spring in. Finally I realized that the spring had to be placed with the tip that sticks out against the wall of the dishwasher to make the spring action work. The long and short pins were not a problem. How to place the spring was the main problem, but I finally figured it out. I did not need any special tools to accomplish this. I just used a kitchen knife to push the short pin into place.

This is the second time I've purchased parts from PartSelect.com. Actually called Lowe's parts hotline and got disconnected three times. Went online with PartSelect.com and purchased the items within 5 minutes. Parts arrived within 2 days. Will definitely be purchasing parts from PartSelect.com again when needed!!!

Myscanning other reviews i saw mention dishwahser developed a small leak on RHS of door. I assumed the door gasket and planned to order that. On of the dispenser gromet which is only a $5 part so ordered that as well. I first replaced the door gasket which is an easy 10 mins job and ran the dishwasher again, but it still leaked.

I then removed the 7 torx screws on the door panel which came away easily. It was obvious that water was in there, so i removed the two screw on the dispenser with a nutdriver to replace the grommet. This process took 20-30 mins. After reassembly the leak was gone.

Without the comments on the website i would never have thought of the disepenser as source of the problem.

I used a torx driver to remove the seven screws holding the inside door panel in place. Flipping it over exposed the dispenser mechanism. There were two hex nut screws holding the whole assembly in place and two wires attached to the wax motor. As an afterthought I had ordered the sealing grommet for the latch, and as it turned out, the main problem with the sticking latch was that the grommet had worn out and allowed the hard soapy water to leak into the slider assembly and build up a hard crusty residue that had helped to ware out the old wax motor. After completely disassembling all of the parts, I scrubbed the residue out of the housing, replaced the slider, latch, spring, and grommet. Next I snapped the new wax motor into place and connected the two wires. The whole thing went back in place and the two hex screws went back to hold it all together. Finally, the seven torx screws went back to put the door back together. The whole repair went without a hitch.

We are planning on selling our home and trying to spruce it up a little. We have an old dishwasher - probably 18 years old and it works just fine but the front panel was banged up and scratched. We were actually planning to buy a new dishwasher because it looked so bad until I found out you could order a replacement for the front panel. It was a great and less expensive alternative to buying a new dishwasher. Easy to order and the part got to me in just a few days. Thanks very much.

I used the parts blowup diagram on PartSelect.com and dissasembled the bottom wash assembly. Carefully examining how the washer arm rotated, I determined that the spray arm support nut had broken. The extended top of it has broken off. This nut, when tightened, allows the spray arm to rotate freely. In trying to diagnose the problem, I had even removed the motor assembly at the very bottom. When I reassembled it, I apparently did not seat the gasket well and did not tighten the bolts well, so when I tested the washer, water leaked out the bottom. So, I had to dissasemble it all again and properly torque the bolts. So, I really created another problem during the diagnosis.

turn off breaker
turn off water supply line
note wire color locations on notepad
disconnect 2 spade lugs (pliers)
disconnect inlet line (adj. wrench)
disconnect outlet line (pliers on hose clamp)
remove old valve assembly (4 screws w/nutdriver)
remove ground jumper from old valve
remove inlet pipe ell from old unit (vise & pliers)
clean open end of pipe ell (file)
apply teflon dope tape to pipe threads
install pipe ell on new valve
reorient solenoid 90degrees cw to match Maytag installation
reinstall ground jumper
install new valve assembly in dishwasher
reconnect hose and hose clamp
reconnect inlet line
reconnect spade lugs
turn on supply line, check for leaks
turn on breaker
start washer at appropriate cycle to test water flow
done!