DU401 Jenn-Air Dishwasher - Instructions

My daughter and son removed the old gasket and installed the new one. It went well.

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

found the parts ordered them an poof dishwasher us as good as new

Turn off power, remove the lower kick plate and lower trim panel with the nutdriver. The float switch is in the front on the left. Remove the two wires on the switch. Use a #1 philips to remove the one screw holding the switch to the frame. Remove switch. Install wires on new switch and install switch using the screw. Be sure to get the plastic float arm under the switch. Raise float and observe the switch clicking on and off. Replace lower plates and restore power.

I ordered two springs (PartSelect Number PS2202520), one for each side of my 30 year old Maytag WU704. This is the shorter "assist spring" that sits right behind the slightly longer green-ish spring, of which there are also one on each side. Now, with 2 springs on each side, the door swings like a new unit. I did NOT have to pull the dishwasher out of the cabinet at all. All I had to do was remove the base plate and there are gaps under the dishwasher frame that you can fish the spring with plastic grommet through, to insert the grommet into the appropriate hole on the door lever arm. Then with a pair of long needle-nose pliers I was able to reach from under the outside of the unit to grab the hanging spring hook and pull it down to insert it into the appropriate hole in the frame. I had a series, or line, of holes to choose from for this. I found that the hole closest to where the green-ish spring attaches made the door tighter and hold faster, the hole furthest made the door feel looser. You can do with one spring but I figure two would probably assist each other in lifting and last longer. Easy fix you can do! It would be an even easier fix if you need to replace the two other green-ish springs (PartSelect Number PS2097003), because they are right at the front of the unit. Open the bottom of the unit and check to see which is broken, so you are sure to order the correct spring(s) because they are different!

This was a pain to change due to very limited access. Also belt had very little stretch. Had to really put some thought in it before attempting.

bimetallic latch to release soap cover was broken.
Had to order entire soap cup assembly to get the bimetallic strip. Removed strip from new assembly and replaced broken strip. Put remainder of cup in box and saved for spare parts.

Removed front panel by removing four screws. Used 5/16 nut driver to remove six screws holding dispenser and disconnected two wires. Inserted new dispenser and reattached cover. Longest time taken was to realign cover properly. Best approach seemed to install with door as near vertical as possible and to start screws by hand. ONLY FOUR screws hold the panel in place. Very easy repair for anyone. part arrived sooner than expected.

replaced belt....great service!!

removed screws that secured cover plates. discovered that belt was broken. ordered new belt. ordered friday; delivered monday. read some previous repair experiences.

the trick to getting belt onto the pulleys is to first wrap it around the spindle part. then set the belt into the motor pulley groove. carefully start working the belt in the other pulley into the groove while rotating both pulleys. i had to lay on my stomach on the floor to do this, but it did not take very long. once the belt is in place, lubricate it with the included gel. took about 20 minutes with some trial and error.

It is realatively simple to replace the dispenser cup. Revove the 4 screws on the inside edge of the door (Not the upper screws for the upper
control panel). The front cover will come away exposing the dispenser cup. Using a 1/4 nut driver
remove the 6 (I think) screws after unplugging the electrical connector. (Be sure & replace in the same position.) After removing the screws, the unit will easily come away. Clean the old gasket remnants & crud well and place the new gasket and cup in line with the nut holes.

lostened motor mounts,
streched belt across pulleys,
thghtened motor tension
replaced access panel.

Followed instructions, those were OK.
Dishwasher front still leaking

it was very easy to unscrew the broken nozzle and screw back the new one. !

Changed springs on both sides as long as I was at it. Did this without having to pull out built in washer. Lock the door closed to give the least tension on the springs. Remove kick plate at bottom of washer. Remove small access panels on each side. If you have small enough paws you can reach thru the access holes and strectch the spring with your fingers to remove and install new springs or use needle nose pliers if you have to. Don't forget the nylon bushings that come with the springs or the metal on metal contact will eventually nick the springs hook and make them break . Hook top end of spring first (rounded hook) and then stretch spring by grasping between thumb and index finger and hook into bottom hole. Hardest part is having to lay on your stomach to do it. Reassemble and count the money you've saved.