DW1000B Jenn-Air Dishwasher - Instructions

After performing some maintenance to get the water flowing properly through the system (that's another story) the door was leaking very badly during any test run of the dishwasher.

We thought it was the gasket because the old one was calcified and dried out from years of harder water.

We ordered the new one and in minutes after receiving the new gasket we had a firm seal and our dishwasher was back in action.

I removed the screws on the inside of the door. Removed the cover and changed door switch and holder and put the new one in. Replaced the cover
all in less than half an hour.

The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.

The dishwasher is well engineered to perform this work.

Remove the bottom two panels to provide access and visibility to base of pump motor.

Locate plastic pump locking lever and push toward rear of DW to unlock pump from DW.

Inside the DW remove basketsand spray arms. Revove screws holding cover over pump motor and remove cover.

From below raise pump motor and support with block (piece of 2x4 worked well).

insde DW, removre old gasket, clean well around pump and botom of DW, install new gasket.

From below remove block to drop pump motro back into place, and re-tighten locking lever by pull toward you.

re-assemble inside componets, run through a rinse cycle to test for leaks and replace bottom panels.




I

I was able to remove the old handle and place it on the new basket - using only a screw driver.

More of a face lift really. I purchased a new Frig. it has a stainless steel (brushed) front with black trim. The dishwasher is all black. I purchased a new face in black (no brushed steel was available) Then I purchased a film that I placed over the panel which was stainless steel (brushed) and it looks like a whole new kitchen.

found detailed repair procedure at applianceaid.com which was relatively easy to follow - be aware that after years of service and some corrosion on the motor shaft it may be difficult or impossible to remove the plastic pump impeller and plastic drain impeller without damaging to get down to the shaft seal - the repair is not difficult for anyone with mechanical skills but I did have to order the two impellers and await their arrival before completing the repair.

The replacement of the spring linkage was simple - the pulling out and pushing in of the under-the-counter dishwasher was the difficult and time-consuming part. The repair of the part took less than a minute.

The actual repair -
1. Hook the linkage to the dishwasher door
2. Hook the spring to the dishwasher base
3. Hook the spring to the linkage.

Getting the dishwasher out to be able to make the repair involved:
1. Unscrewing the base panel (6 screws had to be removed)
2. Unscrewing the dishwasher from the counter (two screws)
3. Turning off the water supply
4. Disconnecting the inline water supply from the dishwasher.

Once the part was replaced, I had to return the dishwasher to its original position, which meant performing the four steps (in reverse) used to pull out the dishwasher.

Removed old gasket and foam strip. Cleaned area. Installed door gasket. Trimmed foam strip to fit and installed.

Leak has stopped!

Diagnosed potential problem from scematic diagram found at Parts Select .Com by entering model #. It was very likely the inlet water solenoid. Tear down was simple: Turn off water, disconnect water lines to and from solenoid, disconnect two electric terminals and remove part by removing two screws from dishwasher chasis. Before you buy the new solenoid, unscrew the water inlet elbow from solenoid and check the filter/screen inside the solenoid to make sure it isn't clogged. Assuming it's not, order the replacement part and reinstall in reverse order. Be sure to use plumber's tape on screw connections to make sure there are no leaks..... Also for ease of acces, you'll need to turn the dishwaher down on it's front. Put towels down to cushion the front and keep the controls from contact with the floor. Good luck!!

First I disconnected the dishwasher electric, water supply and discharge hoses. I then pulled the dishwasher out. After opening the door, I removed the retainer clip holding the upper wash arm, then the nut holding the top shower hose in place. Close the door and lean the dishwasher on its side to get at the underside where the other end of the hose is. Loosen the hose clamp and remove the top shower hose. Reassemble everything in reverse order. In hindsight, I didn't need to buy the new hose clamp or the tub top washer (I reused the originals). Good luck!

I removed the seven screws from the back panel of the door (special tool) and seperated the back panel from the front. My wife held the back up and I removed the two wax motors (detergent cup and rinse aid), which were clipped in place. I had turned off power to the dishwasher, so I simply unplugged each wax motor from the wiring harness, plugged the wax motors in and clipped them in place, making sure that the wiring harness was put back in the same place. Then I put the back panel back on the door, turned the power on and tested the repair. The dishwasher worked perfectly. Thanks to PartSelect for helping me solve the problem. The parts arrived in two days!

I took out both wax motors - tried switching the motors on the rinse dispenser and soap dispenser but they were both dead - new motors from partselect arrived fast - simple installation if you have the torx screwdriver for the door inner panel.

We simply removed the old gasket which was corroded, cleaned up the hard water buildup, and popped the new gasket into place. The problem was fixed! No more leak!

very easy to replace! !

Remove the retaining screws holding the inner door panel in place. Then lift the panel away,make sure you unplug the wiring connector there noting the way it was plugged in.

Then remove the screws holding the stainless trim panel in place over the latch assembly area. Unscrew the screw retaining the latch/switch assembly, unplug the connectors on each side of the two switches,assemble the new latch/switch assembly and install ! !