JDB3010AWE Jenn-Air Dishwasher - Instructions

Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.

The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.

Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.

New pump housing filter was needed as the old one was plugged and distorted.

I

Removed top retaining piece by turning clockwise to remove spinning spray arm from bottom assembly. Removed the 6 retaining screws from the primary screen pump cover and lifted up. Removed filter and the four pronged piece that spins with the filter. Removed the 3 hex head screws that held the secondary filter assembly & pump cover in place. Removed center screw that held the bottom black plastic piece just above the secondary filter bottom. Inspected the cutter, then started reassembly in reverse for the replacement of new parts and filters.

Basket Replacement very simple just remove old and set new basket in place

I discovered that, except for the central tower, all the spray holes were all plugged with I took to be calcium deposites . Using the parts diagram located on this web site, I removed parts. All parts can be removed either by hand, nutdriver or small wrench however you do need a star drive (simliar to an allen wrench) to remove the Pump Cover and Secondary Filter. The Lower Spray Arm unsnaps from the Pump Cover and Secondary Filter. I laboriously removed the deposits from each part down as far as the support filter. The upper spray arm can be removed by unsnapping the hub. the Pump Cover and Secondary Filter is a closed unit so. I purchased a new one. The process is very labor intensive. Next time I am going to consider purchasing all new parts or calling a repair man.

Removed old gasket and simply replaced it with the new one. Very easy.

pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.

I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.

unscrew screen and cover and unbolt impeller replace with new parts. everything goes back together easily, anyone with even minimal repair skills should be able to do this repair.

removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.

still leaks - will investigate further

Shut off the water and electric then removed the cover at the bottom then removed the water inlet valve and replaced it with the new one. Turned on water and electric. Replaced cover at bottom. Very easy and the part was shipped quickly. No problems and the dishwaser works great now!!

First I replaced the door gasket as every one else. This cut drips about 30%. I then discoverd that the Rinse Aid circular dispenser cap was opened about half way. I turned the cap tightly clockwise to close and cut drips to 90% total. I czn live with the other 10%,

Had a repairman come to clean out all the food that had gathered at the base. Once he showed me how to take the spinner off I was able to order the parts and install them in no time. It works great now. Repairman and parts cost me $100, better than buying a new one.

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring spoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!