DW730W Jenn-Air Dishwasher - Instructions

Pulled out the old gasket and pressed in the new one. No more leakage.

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

I used a voltmeter to see if 120 volts was present at the right time in the cycle; it was, so the actuator was the likely culprit. I ordered one on a Monday afternoon about 2:30, and it appeared on my doorstep Tuesday, shortly after noon! It took less than 15 minutes to replace the actuator - removing the 7 Phillips-head screws, lifting the panel, popping out the upper actuator, removing the two wires, putting them on the new actuator, popping it in and putting the panel back on. Worked like a charm. Happy wife . . .

just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .

romoved 3 screws, removed spray arm support nut. pulled off spray arm support, replaced new spray arm support and spray arm support nut

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.

Popped off the plactic screen filter (3 screws). Droped in the new Spary Arm and put back together.

You guys are AWESOME! I ordered the part on a Wednesday afternoon and received it Thursday morning. So all and all I didn't even have to wash any dishes by hand.

removed lower dish basket. then removed 3 screws lifted element cover and removed center hold down nut lifted spray nozzle nad installed new parts. dishwasher is working like new.
thanks for asking.

Removed dishwasher door liner and removed soap dish door latch assembly. Removed latch from assembly and replaced with new latch. Had trouble replacing assembly in correct sequence. Had to go on line and look at sequence picture to replace assembly correctly. Installed new gasket and replaced liner in door. The new gasket and latch solved my leak problem.
Thank you PartSelect

The dripping water was coming from bottom right side of the door, almost directly beneath the detergent dispenser. Looking closely at the drips, I could see that they were coming from saturated insulation that is between the inner and outer door layers. I took the inside piece of the door apart and sure enough I could see water had been getting through the door latch and running down the inside of the door. I could see that the grommet around the door latch was cracked and brittle, so I replaced it and was pretty sure that would resolve the problem. But when I put the door all back together and did a test run, I had a leak even bigger than the first, but this leak appeared to be through the door seal at the bottom right. I then ordered a new door seal, which took only 5 minutes to replace and resolved the leak. I think the old door seal was too worn out at that spot and just by removing and replacing the inside door layer, it must have not made a good seal at that point. But I recommend starting with the door latch and grommet first, since that is a $4 part, and then proceeding with the door seal, a $43 part, only if necessary.

I tried tightening the latch (this had worked once before), but it was already tightened as far as it would go, and door still leaked. So I suspected the gasket, because the old one looked like it had lost its elasticity and was caked with crud. I tried cleaning it in place, but it still leaked. So I ordered a new gasket. However, it was back-ordered, so I tried removing the old gasket and cleaning it. It came out very easliy ( I had expected it to fall apart). Then I cleaned it good under running water, kneading the crud out of it. I also cleaned ou the groove, then I replaced it and that fixed the leak. So I didn't need the new gasket.

Access to the soap dispenser is easy just screws. One of the two hex head screws that hold the mechanism assembly is buried by a lever and required a with a special offset wrench, I used bent needle nosed pliers to loosen and remove the screw quarter turn at a time. The blocking lever was a snap-in and maybe could have been removed with high force, not generally recommended for 14 year old plastic parts. In hindsight I would use a digital camera to record the mechanism, due to a absence of any detail cartoons of the assembly. The lever arm load spring required tweezers to remove and re-install.

Changing the valve only took about 30 minutes but reusing the fitting from the old valve I could not get it to stop leaking on the copper side of the fitting. I ended up going out and getting a new fitting and cutting the copper line to make a new connection. Then the problem was solved.

I disconnected the dish washer and pulled it out. I laid it on its back, unplugged the electrical wires,removed the electrical magnet and pried the shaft seal out with a flat screwdriver. I gently packed the new seal into place with the flat screwdriver. I connected the electrical magnet and wires. I then installed the dish washer and ran it through a cycle. I am pleased to say the dish washer does not leak now.

Turn off power, remove the lower kick plate and lower trim panel with the nutdriver. The float switch is in the front on the left. Remove the two wires on the switch. Use a #1 philips to remove the one screw holding the switch to the frame. Remove switch. Install wires on new switch and install switch using the screw. Be sure to get the plastic float arm under the switch. Raise float and observe the switch clicking on and off. Replace lower plates and restore power.