IKU58660 Inglis Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from LEONARDTOWN, MD
- Parts Used:
- WP3379383
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
broken door spring
Pulled dishwasher out from counter. Took cover off and replaced door springs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timmy from NEWNAN, GA
- Parts Used:
- WP8530929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The AIR Lock was on and could not get do anything the repair man said he cannot get the part and buy a new one dishwasher I got on. The internet and founded part select and they had the part I need and with the repair video was easy thanks partselect
I follow the video and it was easy thanks! you save me money and my old dishwasher Timmy S. GA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SUGAR LAND, TX
- Parts Used:
- WP3379369
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The upper sprayer consists of a plastic spinner attached to the top of the washer.
This spinner is attached to a plastic module PN WP3379369 which is held in place by two screws to the top of the dishwasher. I was able to temporarily reattach the spinner by using a hot soldering iron to melt the nylon axle that goes through the spinner. By using a very small metal washer placed on top of the spinner I was able to melt enough off the end of the nylon axle so as to keep the spinner in place and still be able to rotate. By far the most difficult part of this repair is removing the two stops that prevent the upper washer rack being removed from the machine. Doing so requires using a pair of long nosed pliers and taking note of what needs to be squeezed. Even if installing a new part the upper rack needs to be removed in order to get access to this central part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from IONIA, MI
- Parts Used:
- W11169039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
cut wire in center sprayer to remove plastic holder for new basket
after that every thing went very well
Was this instruction helpful to you?
Thank you for voting!
lower spray arm nut broken, upper wash assembly was broken
just put the pieces where they belonged and tighten the screws. it longer to figure out how it was supposed to fit than the actual fixing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from West Babylon, NY
- Parts Used:
- WP3379369
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Upper wash assembly broke off
used a screw driver, removed 2 screws, removed broken piece, screwed in new part ....all done :)
took less than 15 minutes to do*
i just wanted to let everyone know..I ordered the part on a monday and received it on wednesday I was amazed...the part fit perfectly ...and was very easy to install myself....ty so much ...
took less than 15 minutes to do*
i just wanted to let everyone know..I ordered the part on a monday and received it on wednesday I was amazed...the part fit perfectly ...and was very easy to install myself....ty so much ...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Nashville, TN
- Parts Used:
- WP3379369
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The upper Water dispenser fell apart
It was very simple, the repair took less than 5 minutes start to finish. I removed the top dish rack, took out two screws and the broken part slipped right off the water feed tube. I slipped the new upper wash assembly on the end of the tube and replaced one screw. My dishwasher is an older model and the new part only has a hole for one screw but I cannot tell any difference in stability or performance. I put the top rack back on and the dishwasher is as good as before.
Was this instruction helpful to you?
Thank you for voting!
The washarm bearing ring was completely worn thin and the lower washarm had a greater than usual wobbling
First I removed the nut holding down the lower washarm in place. I then lifted up the lower washarm where it's held in place by the nut. I replaced the two new parts: The lower sprayarm seal that seats underneath the lower washarm and the washarm bearing ring that seats on the top of the lower washarm just underneath the nut. A schematic parts list diagram can be downloaded on the KitchenAid website. The wobbling motion of the lower washarm still seems to have the same amount of play as it had before I replaced the two parts. The lower washarm itself is in fine shape including the nut. I even attempted several other different ways to install the seal and bearing ring, yet the washarm still wobbles when I manually spin it. I called KitchenAid to find out if wobbling of the lower washarm was normal. Unfortunately, the person I spoke to didn't seem to me to knowledgable enough in this area.
Was this instruction helpful to you?
Thank you for voting!
lower spray bar bearing rings
Removed spray bar by removing the plastic finger thumb screw and replace as shown by you web page. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from Debord, KY
- Parts Used:
- WP8268873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The nut that holds the lowere sprayarm on broke.
Simple easy twist on and off replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Althea from Vancouver, WA
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking Dishwasher
I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from Bowdon, GA
- Parts Used:
- WP9742946
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water was splashing on the floor during cycle
When water started splashing under the door and onto the floor, I noticed that the spray arm was wobbling. The retainer nut was broken, so I ordered it as well as the spray arm bearing ring. After I put them on, it still wobbled and splashed water. That is when I studied the diagram on the web page and noticed that my wash arm bearing ring was broken. So, order all 3 of these parts and your dishwasher will be repaired with no effort at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Roanoke, VA
- Parts Used:
- W11027965
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My original part was broken. Almost unusable.
Replacement part came. It was broken. I took pics of it, and send the pics and an email to PartSelect. They put another replacement part in the mail on the spot. I was shocked! The 2nd one arrived in perfect condition. BONUS POINT to PartsSelect!
Tom Houser
Roanoke, VA
Tom Houser
Roanoke, VA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Union Bridge, MD
- Parts Used:
- WP8268645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Wheel on lower rack broke.
New one snapped right into place.
Was this instruction helpful to you?
Thank you for voting!