GSD2200G01 Hotpoint Dishwasher - Instructions

I took the inner door panel off as described by others on this website, cleaned out all the gunk left by 27 yrs of use, and replaced the door gasket and tub baffles. A Phillips-head screwdriver was required to remove the door panel, but no tools were required to replace any of the parts I ordered. I didn't find it necessary to soak the door gasket in warm water as it was pretty flexible right out of the package. I recommend stretching the gasket slightly while pressing it into the groove, particularly around corners, or it will end up being too short at the end. The rinse aid tank had also been leaking Jet-Dry for a long time, so I cleaned that mess up as well and tried to replace the tank. Unfortunately, the new tank did not fit my model of dishwasher even though this website and GE's stated that it did. The shaft on the tank that pokes through the inner door panel to the inside of the dishwasher was too short because >2 mm of it was taken up by a thick rubber washer and a hard plastic collar (fused to the shaft to hold the washer in place) that had not been part of my original rinse aid tank. PartSelect was very good about refunding me for the incorrectly identified rinse aid tank and stated that they would contact GE about correcting this error on their website as well. I therefore cleaned up my original rinse aid tank, rinsing out all Jet-Dry residue inside it, and put it back into the inner door panel. I researched this part and found that GE has redesigned it twice since my dishwasher was manufactured in 1985 -- my original part is no longer available anywhere. So, I will just not use Jet-Dry and will maybe upgrade to a dishwasher powder that includes rinse agent (e.g., Cascade Complete). Replacing the gasket and tub baffles and cleaning up my original rinse aid tank stopped the leak for less than the cost of a repairman's service call and diagnosis fees -- it would have cost me 3X more if he had provided the parts and done the repairs! Replacing my dishwasher was out of the question as they do not make them like they used to (i.e., no microchips or motherboards to fail in a few years) -- this is the first problem I've had with my dishwasher in 27 years! As a side note, I also learned from my research that my front door panel insert is reversible. I was able to remove a side trim piece, slide out the panel, and turn it over so the color is now white rather than the outdated almond. It's like I have a brand new dishwasher that is ready to go for another 27 years.

1) Remove kick plate of dishwasher.
2) Release DW from cabinet.
3) Slide DW forward 6-8" to reveal existing door springs.
4) Lift spring off of door and release spring from frame. Reattach new spring.
5) Slide DW back to original position; reposition to cabinet, and reattach kick plate.

1. Remove access panel under door. 2.Shut off hot water.3. Shut off electric to washer.4. Disconnect water line from water inlet valve.5. Remove small outlet water line from valve. Replace valve & reconnect. OR !!! 1.Take solenoid valve & bracket off of original inlet valve 2. Pull out white plastic diaphragm cover. 3. Remove diaphragm & clean out water holes with a pin. 4. Reassemble valve. 5. Reinstall original water inlet valve & save $27.00

First I removed the old gasket and seals. I replaced the seals and had difficulty getting the gasket to seal at the bottom of the door. I had to remove the seven door screws and was able to manipulate the gasket. Do not lift the inside door cover too far, as the latch may become disengaged, thus creating another problem to repair. I did this repair myself (female).

I received my dishwasher as a hand me down, my Aunt never liked the way it cleaned. After it sitting for about 2 years i installed it in my house and found that it leaked all the time from where motor shaft went into the pump housing. After disassembling everything and scouring parts sites online, I found the parts, ordered them. 3 days later i had the parts, and the next day I had a fully functioning leak free dishwasher.

The hardest part was figuring out how to disassemble the door to replace the baffles and door gasket. No pictures or clues on the internet or my owners manual. I figured it out myself and the rest was a piece of cake. When the 7 screws were removed, the door liner lifted right out and new parts fit right in.

I simply detatched the broken old roller and snapped in the new one. It was very simple and I did not need any tools.

first, I removed the screws holding the dishwasher to the countertop.Then I removed the dishwasher from under the counter. I turned the dishwasher on it's back and loosened the three hose clamps securing the water connections to the pump assembly. I then removed the electrical plug to the motor and the screw holding the support rod to the motor. Then I worked the loosened water connections apart and removed the pump and motor assembly.
Then I removed the hose clamp and plug from one of the orifices on the new pump, and aligned all of the water connections and wiggled the new pump assembly into place. I tightened the hose clamps, Installed the new screw and support bar to the motor, and connected the electrical plug. I then turned the dishwasher upright, reconnected the power cord, water supply and drain lines and started a wash cycle to check the new system for leaks. I found that the extraneous drain solenoid that came attached to the new pump was loose and rattling, so I secured the solenoid shaft and linkage to the pump housing with electrical tape to stop the rattling.

I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

I replaced the top filler tube. (The $65 price for the filler tube is outrageous. Glad I didn't have a service man fix it. With mark-up it would have cost me over $100 for a 3 foot plastic tube. Crazy!)

While I was add it, I replaced the corner tub baffles.

Removed the dishwasher, turned it over, removed 3 hoses, 2 clamps, 2 wires and one support. Installed new pump and reconnected. Done!

Shut off circuit breaker to dishwasher and shut off valve to dishwasher under sink.Remove bottom access panel screws on both sides of panel. Remove both screws holding dishwasher to counter.Place old mattboard strips under legs to prevent scratching floor & slide out from under counter. Use a Shopvac to remove water and spillage. Have rags and paper towels handy. Carefully disconnect wires, drain hose and water line to free dishwasher. Fold old rug runner in half to place dishwasher on, turn on side and then gently upside down on rug to access motor. Remove butterfly clamps, hose clamps, electrical connections, and support bracket. remove old motor and pump and place in box to discard. Position replacement motor and pump according to diagrams. Reconnect all clips, hoses and connections. Since replacement motor and pump is smaller, use longer support bracket from adapter kit. Return dishwasher to upright position and reconnect wiring using wirenuts, drain hose and waterline. Reposition mattboard strips under legs and slide back into place. Attach screws to counter top. Turn on power, water and do a test run to check for leakage. Replace bottom access panel. Pat yourself on the back since you've saved yourself hundreds of dollars for a repair or replacement of your dishwasher.

I made this replacement more dificult because I removed the old motor/pump earlier. Should have done it at the time I installed the new unit to be sure all hoses where installed correctly. I hooked the drain hose to the wrong port and when I started the dishwasher I found my error. Once I corrected the problem and started it again - the wash and drain cycles were perfect and there were no leaks.

I popped off the front track stops--pretty easy with a little twisting and slid the basket out. A little leverage with a screw driver and the roller axle slipped off easily. Popped the new ones on, slid the basket back into the track and popped the stops in place and the job was done in under 15 minutes.

Since the pump and the motor was a single unit, I removed the assembly by disconnecting the electrical plugs and drainage connections. This was a very simple installation. I reversed the above steps, reinstalled the dishwasher and all worked out well.