HDA3230Z07BB Hotpoint Dishwasher - Instructions

Unscrewed bottom of spray arm support assembly counterclockwise by hand for removal. Inserted new part and screwed it in clockwise by hand for installation. Worked perfectly. Video was helpful.

A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.

The repair could not have been more easy! We simply unscrewed the broken spray arm and screwed in the new one. For less than $50, we fixed it ourselves. We would have paid in excess of $350 for the repairman to fix it. We could not be more happy with this website, the videos and the fast delivery!

As per instructions from this site I simply unscrewed the entire assembly and installed the new spray arm assembly. The old unit was a bit stubborn due to age so I used the long handle of my favorite screwdriver, inserted through the bottom area, for leverage. The entire process took less than 5 minutes. Very simple and as a side benefit, the dishwasher operates much quieter than before the old spray arm broke. Guess the old arm was also worn out before it broke on this 18 year dishwasher.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

Used drill and easy out to remove broken part, then put in new one

Turned off the electricity to the dishwasher,removed the old solenoid,and put the new one on(very easy),turned the electrical breaker back on.

Opened package, removed cap and screwed it in place.

Identified solinoid responsible for the operation of the drain flapper valve had become damaged, possibly due to its coil shorting and overheating, the inside plastic insulation then melted and came up through the solinoid pin hole. I removed the tension spring holding the flapper drain valve shut, removed the eclip holding the white phenelic arm connected to the tension spring, removed the two screws mounting the solinoid assy. I threw out the bad solinoid. I then proceeded to install the replacement solinoid in reverse order of removal. The end. Works like a champ ! Thank you for your quick shipping response time. My wife is now once again happy. As you know, if my wife isnt happy, I sure wont be happy. :)

The instructions were excellent, The repair was simple. The order process was excellent, as well as the delivertime. Part Select offers excellent bluline breakdown as well as east access to help which I did not need. Thank you Part Select for yor excellence of service.

REmoved the bottom to plates on the dish washer
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.

After removing the front panels, I removed two screws holding the valve in place. I turned off the water supply and removed the water line, unclipped the hose clamps and took the faulty valve out. I then reversed the above steps and turned the water back on. NO leak. Very easy to do andthe repair took ~20 minutes to complete.

Turn water off and unplug unit first. I remove the 2 retaining screws under counter, pulled out dishwasher. I laid it on it's side to get to pump, loosen up Hose clamps on inlet and outlet ports on pump. You may need a towel or rags to soak up a small amount of water from hoses and old pump. Removed the two hoses on the side, note the lowest one is the drain hose. Un plug all wire connections and loosen support bracket. Removed old pump and installed new one in reverse order. I had to use the 90* adapter hose and the white adapter for my drain hose.The kit contains all adapters and it all fits perfect. Reinstalled and tested unit worked great!!!

Recieved universal parts f/ pump & mtr assy. sorted them out, picked the ones I needed to complete my repair. Installed new assy, checked operation and was completly done in about an hour.

My old bones needed a break, or I could have been done faster. All's well, and the dirty dishes are back getting cleaned via machine, and not us.

After checking to make sure the filter wasn't clogged I removed the faceplate and, poking around a bit realized that the solenoid that actuates the drain valve was jammed. Removing it was was simply a matter of removing a pin and two screws. I reattached the new part, the only difficult part was holding the part in place while reattaching a few springs. Closed it up and its working like a champ.