HDA2000F04BB Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Corvallis, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid fill cap broke off at base
I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bradenton, FL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes cloudy, spotting
Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Nespelem, WA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Wouldn't clean upper rack, not enough water
Checked the water supply to the inlet valve - OK, pulled the filler hose from the outlet side of the valve and checked flow in wash cycle. Results, less than 1/2 gallon. Checked your website, found 94% sucess rate by replacing the valve, so I ordered one. It took about 10 minutes to install with a nut driver, 6" adjustable to connect water supply, and plier to hold outlet clamp open to install it; now we look forward to dirty dishes rather than dumping water into the machine it takes care of itself and we once again get sparkly cups andglasses of the top rack. OU- Rah!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delia from Ocean, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
no water was being supplied during certain cycle
door gasket dried out due to not using the dishwasher very often and needed to be replaced. removed door, replaced gasket, and re-installed door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- diana from sweetwater, TN
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the dishwasher was leaking at both front sides
i first order the corner baffles and put them in. no change at all, still leaked terribly. the old baffles looked pretty good so i kept them. i then ordered the door gasket and the insert. i removed the old one, put in the new, and still no change. i thought perhaps the machine hadn't been used at all because it was like brand new inside, and previously owned by 'a little old lady'. i decided to load it up and run it on a regular wash, and have done that three times now. it drips a very small amount on the left corner but i'm quite happy that it decreased so much. I think perhaps the seal might be setting with the heat of the cycle because each time a load goes through it get less and less drips from that corner. The first order was sent by ups and they couldn't find where i lived so i actually had to go pick them up, but the second order was sent fedex and they had no problem finding my home, and i was very pleased with how fast my order came.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bay Village, OH
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
water inlet valve stuck open (frozen??)
after watching related video on partselect.com, diagnosis and repair couldn't have been much simpler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark L from Dover, DE
- Parts Used:
- WD27X10223
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Panel looked lik an import. Holes did not line up with factory holes.
Held panel in place and drilled holes and installed drill screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Bayside, NY
- Parts Used:
- WD08X10057
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Small leak at the bottom of dishwasher
Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy from moreno valley, CA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
dishwasher would not fill with water
Researched problems on internet,based on info ordered part. Got it in 24 hrs.followed package directions. So easy and for less than a service call! Runs like a charm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Davenport, FL
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hing arm broke
Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewellyn from Clarkston, WA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
No water fill to dishwasher.
Replaced the water-fill solenoid valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLY from SAN LUIS, CO
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
Valve was leaking. This is the second one that has leaked.
Remove front shields on bottom of dishwasher. Shut off dishwasher and electricity. Unplug electric connection. Unscrew brace holder screws on front. Remove clamped on hose at back of valve. Unscrew valve from copper water pipe. Screw on new valve to copper water pipe. Put on clamped hose. Screw on bracket. Plug in electric connection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas E from Lexington, SC
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
water leaking on floor under dishwasher
Laid on floor remove two small bolts with nutdriver,loose water line with wrench,remove other water line with pliers.Remove water inlet valve and replace with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlon from McRae, AR
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Water would not fill.
Wow, could not have been easier. The suggested repair stated that the water inlet valve was the problem 93% of the time. And, it was spot on. It was the exact same replacement part. And, once installed, it worked like a charm. I have bookmarked this website, and will use it for all future appliance repair. I simply could not be more pleased. It was a breeze. Thanks,
Was this instruction helpful to you?
Thank you for voting!