HDA3600H50WW Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Oak Hill, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
4 wheels missing from diswasher rack (lower)
removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from The Villages, FL
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cap broke
The end cap took about 2 minutes to replace. I received my part quickly and installed it really quick and easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Lake Elsinore, CA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rack end cap was missing.
I installed the end cap by pushing the new part on to the slide rack ,right rear side
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Broomfield, CO
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack slide end cap broke.
I put the new cap in. POC.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Rockland, MA
- Parts Used:
- WD12X10304
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
the top part of the dishwasher down to bottom
first i see if i could move the metal piece it wouldn't move si i used a flat head screw drive to fix it . the end piece was to long so i cut a piece off it fitting it is not moving
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Chatham, NJ
- Parts Used:
- WD35X21038
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
wheels colapsed
replaced new wheels
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Nashville, TN
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Several
There is nothing to tell I order send to location and their maintenance installs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Loving, NM
- Parts Used:
- WD26X10051
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Dishwasher pump was frozen
Ordered pump mechanism and replaced defective pump. A very easy replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hampton, GA
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door had no resistance/no balance/would fall open
First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Alexandria, VA
- Parts Used:
- WD35X21038, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost wheel
just snapped the new part in. couldn't have been easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from Keller, TX
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
SOmehow the upper rack end cap went missing. I needed to replace the cap so the rack would not pull all the way out and fall down.
I used needle nose pliers. I bent the stainless steel guide arm out so that I could insert the end cap. Once the end cap was installed I used the same needle nose pliers to "pinch" the guide arm back tight around the end cap. The end cap had premanufactured "notches" to hold the end cap in place once the guide arms are pinched down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carole from Libertyville, IL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken lower wheel ion lower dishwasher rack
Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard E. from Houston, TX
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dishwasher rack rusted
Removed the old rack and slid in the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlene from Canyon Lake, CA
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
There was no problem, out of the box, into the bottom of the dishwasher.
No repairs needed, just replace the lower dishrack with 2 broken wheels with the new dishrack with the wheels already attached. Easy as A,BC or 1,2,3.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Ames, IA
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
serious rust & corrosion on the rack
just lifted out the old one & replaced it with the new one. Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!