HDA2100H35WW Hotpoint Dishwasher - Instructions

Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.

Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.

1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

The sump was very clogged with caulk like crud that we think was a chemical reaction from soap that was used the first two years. When I first started troubleshooting, the sump seemed to be the problem, so I replaced that. There was a small hose on the sump that was broken so it made sense to replace it anyhow.

When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.

I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.

Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.

My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.

TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.

Per ps video. Really easy. Disconnect power, Remove front lower panel, remove Power leads, 2 installation bolts, remove 2 spring clamps on feed/exit hoses,reinstall.

I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn

I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.

I turned off the water supply to the dishwasher. Then took off the front panels and disconnected the water. I then unscrewed the dishwasher from the countertop, pulled it out luckily there was plenty of play in the wire, and drain hose. I turned it on its side and had to remove a couple clamps to free th piece that I was replacing. Once I got to it, it just unscrewed. I put the new one on and everything back together. It was easy.

This is a very simple fix. The majority of work comes from getting the unit out of it's enclosed space so it can be worked on. Once the dishwasher is out in the open, lay it on it's side, and simply unscrew some metal clamps, pop out the bad part, replace it with the new, reattach the pieces and clamps, and start putting the unit back in place.

I'm just happy I was able to actually find the part to begin with, and then to make the changes myself is a very rewarding feeling. Instead of missing time from work and shelling out $150+ to have an appliance repair man come out to do the work, I spent $20 for the part, and maybe an hour total to make the repairs.

I'll be back to this site in the future if/when other parts on other appliances go bad.

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..

removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you

My husband said it was easy. But the gasket didn't solve the problem. So we had to order another part. We had to order the little black stoppers that go in the hinge area. Still leaked so my husband took them back out and cleaned the area. Then put some kind of sealant in and replaced the black robber things. So far that worked.

No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!

placed the end cap into location and forced it into place. Fixed -and we are all much happier!!