HDA2100H50CC Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joyc e L. from Prosser, WA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack kept coming off slider due to broken end
Popped in the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Lake Elsinore, CA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rack end cap was missing.
I installed the end cap by pushing the new part on to the slide rack ,right rear side
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Silver Spring, MD
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack end cap was lost or missing
All I had to do was slide the rack forward slightly, reach back to the end of the rack and snap the end cap into place. It helped to have someone there to balance the rack while I was replacing the cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Loving, NM
- Parts Used:
- WD26X10051
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Dishwasher pump was frozen
Ordered pump mechanism and replaced defective pump. A very easy replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Rockland, MA
- Parts Used:
- WD12X10304
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
the top part of the dishwasher down to bottom
first i see if i could move the metal piece it wouldn't move si i used a flat head screw drive to fix it . the end piece was to long so i cut a piece off it fitting it is not moving
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Chatham, NJ
- Parts Used:
- WD35X21038
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
wheels colapsed
replaced new wheels
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Nashville, TN
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Several
There is nothing to tell I order send to location and their maintenance installs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Alexandria, VA
- Parts Used:
- WD35X21038, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost wheel
just snapped the new part in. couldn't have been easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from Keller, TX
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
SOmehow the upper rack end cap went missing. I needed to replace the cap so the rack would not pull all the way out and fall down.
I used needle nose pliers. I bent the stainless steel guide arm out so that I could insert the end cap. Once the end cap was installed I used the same needle nose pliers to "pinch" the guide arm back tight around the end cap. The end cap had premanufactured "notches" to hold the end cap in place once the guide arms are pinched down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Corvallis, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid fill cap broke off at base
I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Parkland, FL
- Parts Used:
- WD28X31819
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher Racks Were Replaced In The First Order.
When I received the first order the lower rack didn't fit because it wasn't wide enough. Your people replaced the rack and now all works in good fashion. Thx, phil
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- susanne from Moorpark, CA
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dishrack rusted
Instructions for repairs. Remove old rack from dishwasher. Stop, have a beer. Open packing box. Remove new dishwasher rack from box. Rest. Have another beer. Slidey old thingamajig rack ouy from dithwather. Shove into packing box. Figure out where you put the new rack. Pick up new rack, put new rack on countertop. Hav anoder beer. Put nw wreck in dithwather. Take bx & bee botluls to trash. Take nap. :>) S.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Fort Worth, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
miss wheels
It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bradenton, FL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes cloudy, spotting
Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia E. from Metropolis, IL
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic Slide end cap Broke and let the upper rack come out
Put rack in place and snapped new one in.
Was this instruction helpful to you?
Thank you for voting!