HDA2160H50SS Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from WEST DEPTFORD, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was old and leaking.
I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLUMBUS, GA
- Parts Used:
- WD13X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door latch broken
I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn
Thanks GE,
T. Dunn
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from EAST MEADOW, NY
- Parts Used:
- WD14X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Plastic hinge arm link broke
Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from LOUISVILLE, KY
- Parts Used:
- WD21X10268
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water not pumping out of tub.
Repair was easy. However, this did not solve the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SOUTHPORT, NC
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken spring on door.
See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- forrest from stuart, FL
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace door gasket
from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Rockville, MO
- Parts Used:
- WD24X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Couldn't drain water
I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from Flower Mound, TX
- Parts Used:
- WD31X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Toe kick not included
Removed screws and replaced the part. It couldn't of been earlier. Only problem this kit didn't include a toe kick and we are having a hard time finding it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from JONESBOROUGH, TN
- Parts Used:
- WD28X31819
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
NEEDED TO REPLACE LOWER RACK IN DISHWASHER TO SELL HOUSE
TOOK THE RACK OUT OF THE BOX AND PLACED IT IN THE DISHWASHER, DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SOUTHPORT, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap broke
Slide it into the arm until you hear it snap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from PLANO, TX
- Parts Used:
- WD28X31819
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Racked rusted out
Simply removed the old rack and installed the new rack.....easy as 123 ABC. Dishwasher still works fine but the bottom rack had rusted out. Not sure if this is common for this Hotpoint dishwasher as my deciding factor to order from here was that others had the same problem as me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryll from Newville, PA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The top drawer of the dishwasher would extend past the support rails.
The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Davidson, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Cap had broken off the top rack, it kept sliding down
I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donna from walworth, NY
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
upper dishwashr rack lost the end cap and the rack kept coming off the track when you went to push it back in it would jam into the track and all the dishes would bang and fall.
placed the end cap into location and forced it into place. Fixed -and we are all much happier!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Waterville, ME
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Was this instruction helpful to you?
Thank you for voting!