HDA2160H35SS Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carrell from Cochranville, PA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap missing
installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy
wife happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Oroville, CA
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Disrack was getting rusty
Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Cypress, TX
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Upper rack kept dropping from the wheels when we pulled it out
We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.
The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.
The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Clifton, NJ
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dispenser cap would not stay in place because it had melted
First I opened the package and screwed the new dispenser cap into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Shelton, CT
- Parts Used:
- WD16X10011, WD16X313
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
detergent shaft and arm broken
pretty easy, take off 7 screws from inside door
only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)
only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eduardo J from San Angelo, TX
- Parts Used:
- WD28X31820, WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rusted Racks
Replaced lower rack with new. Upper rack removed front stoppers, removed old rack, slit new rack in and replaced stoppers. Total time about 15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathaniel from HAWKINSVILLE, GA
- Parts Used:
- WH23X10028
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Would NOT drain
Flipped washer on side
Did repair from bottom
Really easy repair
Did repair from bottom
Really easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy G from SPRING, TX
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water leakage at valve
I watched the video that came with email on part. Gave instructions on how to. Thank you !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from JONESBOROUGH, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Would not fill with water
Ordered most likely part...water inlet valve.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from DOUBLE SPGS, AL
- Parts Used:
- WD22X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
The telescopic part of the washer was broken.
The part came in as ordered. After removing the dish rack, I loosened three 1/4" screws (two on the strainer basket and one at the base of the spray arm. I had to slide the rubber hose down and back to disconnect the base which I did by turning counter clockwise. The new one went in by reversing what I just described. Other than two of the screws being difficult to reach, everything worked fine.Thanks for your site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TRAVIS from Webster, MA
- Parts Used:
- WD22X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Broken plastic spray arm
There's a video on youtube from this site on how to install spray arm and base. Great video. Great price
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hillsborough, NC
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Put lower rack in
Took old rack out put new rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Yuma, AZ
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wornout rack
I took out the old one and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from McMinnville, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Damaged rinse agent dispenser
Unscrewed old one and installed the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merle from Boulder, CO
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Severe lwater leak around door
Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!
Was this instruction helpful to you?
Thank you for voting!