HDA3500N00BB Hotpoint Dishwasher - Instructions

knew the cause of problem ordered parts prompt delivery 16 yr grandson did the repair with little or no assistance

look at neww part first then r&r

Water was leaking from under refer next to installed under counter dishwasher. Once determined to be dishwasher not refer I removed dishwasher toe place was able to see dripping inlet solenoid valve. I had to disconnect 11V power, shut off inlet water, disconnect inlet water house and remove dishwasher from under counter. Once dishwasher was in center of kitchen I flipped it upside down and removed the electric solenoid inlet valve. Removing the valve took one wrench to remove inlet hose then two wrenches to remove 90 degree brass fitting and another to hold solenoid. I used a nut drive to remove two screws that released the solenoid from the dishwasher frame. I used teflon tape to reattached the 90 degree brass fitting and inlet hose.

remove front lower cover, 2 philips screws, turn off water supply under kitchen sink to dish washer, turn off power to dish washer, remove water supply line to valve, remove power to valve, clip ons, remove two 5/16" screws holding valve on, turn valve gently to access clip holding washer supply hose, push clip up hose and hold hose while pulling valve off. re-install in reverse order, a flash light helps.

After installing the part, ran the washer once more. The water still remains in the washer. Tried washing several times. The problem is still the same.

Switch off the circuit breaker supplying power to the dishwasher.

Remove the 6 screws that hold the plastic face of the inside of the dishwasher door, and lift out the inside liner. This may be a good time to wash it down, as it is probably a little messy. It may also be a good idea to put something a little heavy onto the door to keep it laying in the open position as the springs will keep lifting it back up.

Remove the screw holding the spring device down over the interlock switches and the thin plastic cover and put aside ready for re-installing again later. The spring may have flattened a bit and it may be a good idea to bend the end open, just a little, to give it back some tension. This is the spring that activates the interlock switches when you latch the door.

Unclip the faulty Interlock Switch by pushing (with your fingers) the little plastic clip holding it in and lifting it out of its cradle. If the switch to be replaced is the one furthest from the machine (or nearest the top of the door) you will have to take the bottom one out first so that the clip can be released.

Using small pliers pull the electric connectors off the faulty switch and reconnect to the new switch in the same way that the faulty one was wired.

Snap the switch (or switches) back into place in the cradle.

Replace the spring activator along with the plastic sheeting and screw that back in.

Put the inside of the now clean door back down into place, making sure the on/off lever is inserted through the slot in the front of the door, and that the piece of Styrofoam is inserted back into position.

Screw the screws back in, starting with the one at the top center nearest the on/off lever and then work your way down the sides from top to bottom.

Switch the circuit breaker back on and give it a whirl. Enjoy!

Pull rack out put wheel on put rack back

Quick and easy...a 7 yr old could have done it.

In order to replace the upper dishwasher rack I needed to remove the end stoppers on the sliders. They were difficult to remove and one of them broke. I then ordered new end pieces. The new ones had been redesigned and were very easy to insert. If you need to replace the upper rack be certain to order new endpieces along with the order for a new rack. They are quite inexpensive.

On the front ,lower side of sprayer arm removed the 1/4" screw and you have to stick your head inside and look on the backside of the spayed arm. Locate the plastic clip and gently pry a little just enough to loosen it off the rest of the way, be careful not to break off. It came right off I popped on the new one replaced screw and rain a load of dishes. Thanks for your help and great products for us do it yourselfers.

My son took the part and it plop right into place with a click, and we were able to use are dishwasher again,Thanks

It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.

Check website, order part. Hardest part was determining which was the right part. Needed the axle--I call it the hanger. I had previously called and ordered, but only received the wheel with no way to attach it. Push the axle into the wheel. Push the axle onto the rack. Since it was new, it didn't slip right on, and had to push it hard. (However, when it snapped on, three of the other wheels and axles came off.) Had to put them back on as well. Much easier, as they were older and not as snug. Total time: Took longer to open the package than put it on.

Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.

door gasket dried out due to not using the dishwasher very often and needed to be replaced. removed door, replaced gasket, and re-installed door.