HDA3400F00BB Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- E Andrew from Roscommon, MI
- Parts Used:
- WD22X10008
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
old spray arm broke had to replace
i unscrewed old part and replaced with new one. Didn't know how to do it but figured it our quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from King Of Prussia, PA
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The drain solenoid burned up
Order the part through you guys and also ask to see if there could be something else wrong. I got an e-mail back the first buisiness day and you sent me the part that day also. I installed the coil and it's be running good ever since. Thanks for your speedy service and technical support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Canton, GA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
The pump shaft leaked
I used the pump/motor replacement kit. It was a very easy repair and the parts were a direct replacement with no modification necessary. I saved over $300.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from EAST MEADOW, NY
- Parts Used:
- WD14X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Plastic hinge arm link broke
Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WEST DEPTFORD, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was old and leaking.
I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLUMBUS, GA
- Parts Used:
- WD13X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door latch broken
I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn
Thanks GE,
T. Dunn
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neal from STATESBORO, GA
- Parts Used:
- WD08X10057, WD08X10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher was leaking
I took the inside door off as shown in the gasket insert video and it made much easier to clean and insert the door gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from CARUTHERSVLLE, MO
- Parts Used:
- WD13X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would go on and off during operation
Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from CLEVELAND, OH
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Leaked at bottom of door
I took the inside of door off to install both gasket and gasket insert. Much easier this way. Also it’s much easier to fish locking handle through the door if you extend the handle half way and put through opening when raising the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Georgetown, CO
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Plastic part of inlet valve cracked
Hired my neighbor, who is a plumber.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Terra Ceia, FL
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
The water valve went out
I took the old one off and replaced it with the new one, which fir perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher M from Thousand Palms, CA
- Parts Used:
- WD26X10013
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Pump motor had failed
I removed the two screw at the top holding the dishwasher to the counter top; pulled on the unit - but found it stuck on something.
Of course the hot water feed and the drain hose were still connected and would not let the unit move out any further as there was no slack.
If I had thought about it - I would have disconnected these from under the adjacent sink. But I ended up lying on the floor trying to disconnect them from underneath the unit. It was a bit difficult as there was very little room to move the wrench and the screwdriver.
Once done, the unit came out very easily.
When tipped over I disconnected the old motor and replaced with the new. It was a very different design but fitted in very easily. The hanger took a bit of working out as the diagrams are not very clear.
The wires and clips went together easily. Once I had cleaned everything around the motor and the gunge that cames from years or washing dishes, it went back the way it came out. Albeit with the same difficulty with feed and drain hose.
We ran the unit with no dishes for a couple of times to clear our the muck left in the pipes when the system was down.
Now we have a fully functioning dishwasher again. Cost $250 for the pump and motor as opposed to the $800+ unit my wife was looking at!
Of course the hot water feed and the drain hose were still connected and would not let the unit move out any further as there was no slack.
If I had thought about it - I would have disconnected these from under the adjacent sink. But I ended up lying on the floor trying to disconnect them from underneath the unit. It was a bit difficult as there was very little room to move the wrench and the screwdriver.
Once done, the unit came out very easily.
When tipped over I disconnected the old motor and replaced with the new. It was a very different design but fitted in very easily. The hanger took a bit of working out as the diagrams are not very clear.
The wires and clips went together easily. Once I had cleaned everything around the motor and the gunge that cames from years or washing dishes, it went back the way it came out. Albeit with the same difficulty with feed and drain hose.
We ran the unit with no dishes for a couple of times to clear our the muck left in the pipes when the system was down.
Now we have a fully functioning dishwasher again. Cost $250 for the pump and motor as opposed to the $800+ unit my wife was looking at!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BOBBY from HENDERSON, NC
- Parts Used:
- WD08X10015
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
leakly gasket insert
Repaired by watching the video provided on my computer by this site . This video was a life saver and covered every detail. My thanks to this site !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SOUTHPORT, NC
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken spring on door.
See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from LOUISVILLE, KY
- Parts Used:
- WD21X10268
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water not pumping out of tub.
Repair was easy. However, this did not solve the problem.
Was this instruction helpful to you?
Thank you for voting!